Showing posts with label Atlantic Crossing. Show all posts
Showing posts with label Atlantic Crossing. Show all posts

Monday, February 18, 2019

2017 & 2018: Bless Those Batteries

Ongoing Saga: #11

Solar Panel Regulator, New House Batteries and New Smart Regulator for Alternator.

This was the beginning of a long drawn out and rather expensive saga over a period of nine months.  Sopromar Boatyard in Portugal were asked if they could come up with some charging solution for my three sets of batteries while I was away back home – a single 12 volt starting battery, four 6 volt house batteries and 2 bow thruster batteries.  In the numerous exchange of emails over several months the result was that there wasn’t a solution.  Meanwhile the regulator for the solar panels had malfunctioned, needed replacing and that subsequently the four house batteries had gone flat and needed to be replaced, which they duly did ie solar regulator and batteries.  The old batteries were almost 10 years old – a ‘Trojan’ performance, so probably time for new ones.

At the same time I also had the alternator checked out and we identified that we needed a new regulator for it, which I purchased separately and brought back over with me when I returned to the boat in mid Aug17.  Sopromar fitted the new regulator, tested it and that was that.  Or so we thought.

The bow thruster batteries are AGM and so had held up fairly well and the techo had wired them up somehow so that they received a trickle charge of some sort from the solar panels and didn’t flatten.  AGM batteries can fairly happily sit for up to around six months without any charging and not suffer I’m reliably informed.  

Anyway, to cut a long story short the new regulator was not wired correctly and so the batteries steadily drained once we got underway, except for some charge from the solar panels (which only charge the house batteries and starter battery).  The bow thruster battery charging only occurs when running the motor/alternator.  To add to this mix, we had a generator that didn’t work.

Our batteries were recharged on shore power whilst ever we were in marinas at Lagos, Madeira, Canary Islands and then Cape Verde Islands.  In between were relatively short trips so I wasn’t too concerned as the solar panels did their thing outstandingly and I rarely used the bow thruster.  It was on the 16 day Atlantic crossing that I became fully aware of the charging problem as the starter battery voltage in particular dropped significantly, although I was always able to start the engine when I had to.  

On arrival in Antigua (where we anchored) I had an electrician look at the charging system and he thought it was all okey, particularly when his meter showed 12.6 volts (not the 13 – 14 volts necessary) and he thought the regulator was doing what it should.  He also condemned the house batteries as needing replacement even though they were less than 12 months old.  

No point arguing, so we pushed onto Sint Maarten, initially on anchor but later on shore power at FKG Rigging, where I was able to charge the batteries using shore power.  I also had the house batteries charged and tested at Budget Marine where they were announced as being in good condition.


Next stop was Turks Caicos (shore power in the marina) where another electrician, a friendly French Canadian, made a valiant effort to identify the problem of a very low charge and suggested that the regulator was faulty, only achieving ‘float’ voltage instead of starting with ‘bulk’ and moving through ‘absorption’ and then onto ‘float’.  He also had access to the regulator manual and spoke to the manufacturers but thought it was wired correctly.

We entered the US at West Palm Beach, Florida and then proceeded north along the Intracoastal Waterway anchoring most nights - happily for as long as we had sunny weather.  Unfortunately, further problems were experienced when we had a succession of overcast days and the batteries received very little solar power.   We then experienced some difficulty when anchoring off New Smyrna Beach using the electric anchor winch.  The starter battery was quite sick by now so, with Daytona in our sights, we kept the engine running all night, pulled the anchor up by hand the next morning (thankfully it was clean sand), and made for Daytona Beach.

We berthed in Halifax Harbour Marina (great people and very friendly fellow boaties).  I tried to charge the starter battery using shore power but it would not hold a decent  charge so I had to purchase a new one.  I also consulted with a trusted electrician who had done some work on the boat about 9 years previously after the mast had been hit by lightning.  He is semi-retired now and advised that I should do it myself – every good captain should know how to set up a regulator he said - so read the manual at least three times – and then do what you need to.   I followed his sound advice and found that the regulator was wrongly wired, wired it correctly myself, and now all batteries are charging pretty efficiently, although I sometimes wonder if the starter battery should not be getting a bit more charge.

In summary, three electricians couldn’t get it right, but the fourth electrician gave me best support of all – do it yourself.  Lesson learned, big time.



Sunday, February 17, 2019

2017 & 2018: Oh NO! Not the Generator...

Ongoing Saga: #10

Generator Not Starting and Fuel Line Fitting in Canary Islands
.  
In Portugal the diesel generator had been sitting for 9 months and wouldn’t start for reasons I could not understand, so I had a mechanic look at it – several as it turned out.  They replaced the gasket for the cover over the valves, checked valve clearances, adjusted them and eventually they started it and we ran it several times.  Great.  They did not think the injectors needed attention as ‘it runs so well’.  Anyway, off we went and it NEVER started again.  

When in the Canary Islands I discovered, while trying to start the generator, that a bleed valve over the fuel line was not seating properly as the thread would not allow full tightening.  Ah ha!  I thought, this must be the problem – allowing air into the fuel lines – a definite no no.  Fortunately, a visit to one of the marina chandleries proved fruitful and the very helpful gentleman there found a suitable fitting somewhere out the back of the shop which matched my fitting.   It cost next to nothing too and I was so grateful.  Even so, the generator would still not start.

I had two other mechanics check the generator over for me – in Antigua and then Sint Maarten – and they could not start it.  We didn't have time to wait in the Turks Caicos (the weather was a bit iffy) or I would have had a mechanic go over it there too.  The motor turns over fine but just won’t start.  

The consequences of course made themselves clear as we moved along the Atlantic ICW (US coast) where we anchored out rather than hooking up to electrics at marinas.  See comments on batteries.  The plan is to have our very sad generator checked out again when I'm back in the USA.  Another job for next year...


Wednesday, February 13, 2019

2017 & 2108: Electronic Wizards. Perhaps Not...

Ongoing Saga: # 7

EPIRB Purchase.  I already have two EPIRBS – one PLB and a GME EPIRB, which had a battery that tested okey, but it was past the recommended change date.  So, I thought I should purchase a new one and decided to get an Australian one which would be automatically accepted by the Australian Maritime Authority (AMSA).  The GME was purchased in Oz and brought overseas with me years ago.  I only found that its battery was out of date when I arrived at the boat in Portugal.  

Anyway, I thought that importing a bit of safety gear into Portugal wouldn't be too much of a challenge.  I also understood that courier/shipment companies generally handled customs etc.  As things turned out my purchase was posted via the Oz Post Office which created all sorts of issues.  Firstly, although quickly despatched, it took almost two months to arrive at the boatyard, required a substantial customs payment, and the company that I ordered it from really didn’t show much interest.  I could not trace the item’s whereabouts on route.  The Oz Post Office I assume just send it on its way with no further interest, unlike UPS, DHL, FEDEX that I'd dealt with before.  The company even suggested that I follow up through the Portuguese Customs, which I eventually did once they contacted the boatyard to advise that the package had arrived in town nearby.  Any action beforehand would have been quite fruitless on my part due to being a foreigner, English speaking only, etc.

Once it finally arrived it should have been easy to register it with AMSA via the net but my registration was rejected because an EPIRB with my serial number had already been registered, believe it or not.  It took several phone calls to try to get AMSA to follow up.  Once again the company who sold me the EPIRB showed little interest and just referred me to the EPIRB manufacturer - kti.  By sending emails to both AMSA and kti the situation was eventually sorted.  My serial number WAS the correct one as it turned out and the other registered owner was contacted and provided the right serial number of their EPIRB.

In future if I am overseas and need to purchase another EPIRB, I'm likely to just purchase it where I can pick it up myself; although that has inherent registration issues.  Well, perhaps if my 10 year guarantee remains valid I might not need to.  (I doubt it as I anticipate that some new rule will be introduced soon requiring all current EPIRBS to be replaced in the next 2 years, although perhaps I am being a bit cynical in my old age).   Meanwhile, I have now have 3 EPIRBS, which all test okey.

VHF Handheld Radio.  The old one wouldn’t hold a charge so we purchased another while in the Canaries.

Sky Mate Antenna.  SkyMate is a satphone type comms gear which we installed 10 years ago.   It still operates so we decided that we would just renew our subscription as they advised that our old equipment is still okey but would be better if we upgraded with new equipment costing around 1000 USD or so.  We decided not to and subscribed so that we could use it and get used to using it again.  

Firstly, we had a number of problems with reception, and sending messages.  We contacted tech support, who it must be said worked very hard to solve our issues.  Things dramatically improved when I cleaned the antenna terminals and then moved the antenna away from other antennas and mounted it up on the framing that holds our solar panels above and behind the cockpit arch.  This was a major improvement and we thought it had solved all our problems.

Not quite!  As we were now using the equipment to get used to it but Microsoft (Windows 10) had other ideas.  It would not let us properly send and receive.  Microsoft would say indicate a problem and closed the Skymate.  We devised various ways to bypass and act quicker than Microsoft could hinder us so we got by with being able to send emails, mainly to report our position via message.  Eventually we exceeded our monthly allocation and our emails were rejected but this was fixed, again by tech support, who simply allowed the mails to be forwarded and billed us accordingly.    The fact that there was no notice to warn us we were approaching our limit is a major shortcoming of this equipment.  We were mid-Atlantic at the time and sending regular position reports to our blog.  We will certainly be considering alternate systems for future "blue water" use.

iPad.  My eldest son had given me an iPad and I love it.  Aside from the Kimble application (I do read a lot when sailing) it also takes Navionics charts, so I can have it in the cockpit with me.  The charts are especially useful when entering/leaving harbour.  With further use on the open ocean I found that I would not even bother to go down below to view the CMap chart on our laptop on the chart table.  The iPad Navionics is connected to a small Garmin Bluetooth GPS so that sits below sending signals to the iPad and I just turn it on every now and again to check progress.  So simple and easy to use.

I have even put together a small stand for it: a bamboo cutting board from a Chinese shop, and a clamp fitting that I screwed it to so that I could attach it to a handrail on the steering pedestal.  The iPad is held in place with a couple of small bungee cords.  It has been especially helpful while motoring along the US Intracoastal Waterway and far exceeds the CMap charts usability.  With Navionics you can zoom in and out to infinite settings – whatever is comfortable but zooming in is very important when navigating around channel markers in shallow shoaling waters.  CMap is extremely limited in this capacity; at least using it with the chart program Software on Board.

A couple of drawbacks, however.  While crossing the Atlantic - Cape Verde Islands to Antigua - a message came up from Apple that I needed to re-register and that I could do it from any place that I could access the web.  It locked up the iPad until I did and this all happened mid Atlantic.  Luckily we still had CMap which worked fine.  I wasn’t able to use Navionics again until I reached Antigua.  This is a very REAL safety issue.

Secondly, my iPad is in a waterproof plastic wallet so it is protected in the rain.  If the screen does get wet it will not function as a touch screen, just won’t do anything or will do very strange things so that it becomes unusable.  On one occasion on the ICW the rain was so fierce that I could not use the iPad (and I could hardly see to look for oncoming traffic) so I pulled over just out of the channel and dropped the anchor.  I’m sure there is a techie answer and I’ll put it in here when I find it.



We seem to be going in circles...

Sunday, November 18, 2018

2017 & 2018: In the Yard & Keeping Cool

The Saga Starts: # 1

I've written heaps for 2017 & 2018 years largely because we started in Aug 2017 and remained overseas well into 2018.  Our usual seasonal schedule was out the window, over-ruled by the need to cross the Atlantic again.  I started back in Lagos, Portugal and was unaccompanied for the first several weeks as I wanted time to be able to work on the boat by myself without having to work around other crew, (
namely wife/ GS aka galley slave), on board. (You understand, right?)  I was able to do heaps which was just great and it didn’t matter how messy the boat was.  Sopromar is a great boatyard, well resourced for boating spares, helpful technicians and staff and also in a great location, just a short walk away from supermarkets, restaurants and shops.

I had a couple of major projects planned and as always there's ongoing maintenance.  I also needed to check on all our safety equipment to make sure we were prepared for the voyage ahead.  Given that there's quite a bit to cover and I was busy doing a lot of the work myself, I didn't get round to taking photos.  So, lots of words without the visuals for the time being.  So, let's begin:

Dirty Boat.  The boat was filthy when I got back to it having been on the hard for some 10 months or so.  It took several days and washes before it was back to any decent level of cleanliness.  Nevertheless it had to be washed down every week, such are the prevailing conditions around the Sopromar yard.  There is a dirt car park just in front of the boat and winds/rain loaded with Saharan sand blow across the Med to Portugal.  Nothing you can do about it, just clean, clean, clean.

New Awning.  It was quite hot when I arrived at the boatyard in mid August, so I immediately started work on a new awning to replace the original, which was falling apart.  The fabric was sun shade material which was purchased in Greece many moons ago but for the past few years it was not so slowly falling apart.  I had tried to patch it up using contact glue, which was okey for small repairs or I sewed it using my on-board sewing machine.  Anyway, it was time to replace it and so I brought some sun shade material from Oz.  
The new easy-to-install sun cover keeps us cool & looks neater
I pulled the old awning  apart and used the ‘framework’ of sunbrella material which never seems to deteriorate at all.  I simply used the old shade cloth as a pattern and cut out the new one to the same size (mostly).  Amazing how you think you have accurately copied the old onto the new but, alas no, as you need to be able to stretch out the new cloth so that it is pretty tight before marking the pattern.  This was something I was not able to do well on the yard's cement, try as I did.  So there were a few bits and pieces that had to  be lopped off the new shadecloth when it came to sewing the new shadecloth to the old ‘framework’ sunbrella.  

Anyway, despite these few annoyances and some slight readjustment of lines to various tie down points on deck, it all worked out well.  So we have a nice new strong awning  that takes no more than five minutes to put up and does a great job of keeping the sun and heat off the deck/coachouse.  Took about a week to do, longer than I anticipated but isn’t that always the same with boat jobs.

Companionway Steps.  These steps had been annoying me for years.  It wasn't too difficult to remove 6 timber steps which were badly scratched and showed it.  I sanded them back using the high speed grinder sanding attachment, then applied three coats of water based varnish.  Improved them 1000% and applied each coat immediately after the previous one as they dried very quickly.  Easy quick job that improved the interior of the boat remarkably.

Tuesday, December 10, 2013

2011: Transformers & Electrical Quandaries

Crossing the Atlantic

Repairs Underway: Part 3

240 Volt Transformer.  Our boat, being American, is equipped with 110 volt AC wiring for marina connections, and the on-board generator supplies 110 volts while at sea, to run the inverter/charger, refrigeration, air conditioners, and water heater if (rarely) needed.  In 2011, with Europe being on 240 volts systems, we had to come up with a solution. 

Fortunately, we were not the first to confront this problem and the simplest solution (and cheapest) was to purchase a transformer.  The transformer is one of those yellow very heavy transformers that, I understand, are used by builders in the UK because they have to use 110 volt power tools rather than 240 volts ones (for safety reasons).  So these transformers are widely used.  We purchased ours (500 GBP) early in our stay in the Azores, at Horta at the local chandlery. 

At the same time we purchased an extension chord to connect the transformer to marina power boxes at one’s marina berth.  I installed our transformer in the aft port quarter cockpit locker.  I modified one of the large AC power cable plugs I already had on board (changed an American female plug for a European equivalent) so that it ran from the  transformer to the AC power inlets on the transom of the boat.  In summary, 240 volt power comes out of the marina powerbox to the transformer via an extension chord.  Transformer changes the 240 volt power to 110 volt and this is sent to the AC power plugs at the back of the boat.  I turn on the 110 volt master switch at the electrical panel and we have normal 110 volt power ie charging batteries, running fridges, etc.  

Very simple really and it works a treat.  I also disconnect one of the plugs when I don’t need to use shore power eg when not running fridges, when going ashore etc, as the transformer does heat up a bit and it’s just a habit of mine to disconnect/switch off things if they are not being used.

Pico from Horta Marina

Monday, December 9, 2013

2011: Finally Crossing the Ditch

Crossing the Atlantic

Repairs Underway: Part 2

Genoa Furling Line.  On our trip across the Atlantic the only gear failure was the genoa furling line started to fall apart and had to be replaced with some spare line.  Not a big problem as it turned out.
Doing a little repair job whilst becalmed
HF Radio.  The HF radio worked as it should and we had good communications with the erstwhile and patient Herb Hilgenburg, the benevolent Canadian who guides so may cruising boats crossing the Atlantic.  We could talk to him quite well, most days atmospheric conditions allowing, all the way to the Azores.  We didn’t use him after that as there was only a thousand miles to go – one week.

Spinnaker Winches.  These have proved to be essential for flying spinnakers and they were also very handy for providing a bit of oomph when we needed to furl headsails in a blow, for example.

Hydrovane wind vane self-steering gear.  We used the Hydrovane almost all the way when crossing the Atlantic.  During a gale we found that sometimes the Hydrovane can be overwhelmed.  I have had to manually steer the boat back on course then reset the Hydrovane to, once again, steer the boat.

Skymate.  We had been really pleased with Skymate’s services (accessing weather forecasts & posting position reports daily on our tracker site) as we sailed through Eastern USA, and its initial assistance as WJ3 moved away from the coast heading for the Azores.  However we eventually began to have connection problems due to, I suspect, fewer available European satellites.  Once we’d made it to the Azores, we ditched it all together and concentrated on finding internet and getting weather reports from Weather Online & Passage Weather. 
 
I have to say that it disappointed when we were crossing the Atlantic even though we had told them when we were crossing.  Where it did shine however was "e-mailing" our GPS reports to our map & tracker - a twice daily task that kept friends & family in touch with our exact position mid-ocean.  (It can be set up to report automatically too, though we didn't bother.)  However, we disconnected it once we got to the Med because there is plenty of local coverage with the internet using a dongle on the computer.  More on that later. 

Of course, we still have all the hardware installed and will probably reactivate the system (there’s a reconnection fee if you disconnect for longish periods) when we depart the Med but only after assurances from SkyMate that we will be better served (for our Atlantic re-crossing) than previously.  I might add, when it all works, it’s a very good system & excellent safety measure.
Getting settled in for night shift

In Horta Marina, Azores taking a well earned rest

Sunday, December 8, 2013

2011: A Late Start

Crossing the Atlantic

Repairs Underway: Part 1

Generally, all repairs & modifications took place before we left Deltaville Boatyard. We were thankful for the assistance provided by the Yard’s skilled technicians and their quality work.  
Our plan was to head north to New York City, or thereabouts, then head east to Europe along the 40th parallel.  Simple, until we reached Baltimore and I carried out a last minute check of some of our gear…. 

Rudder Steering Arm.  On inspection I discovered two cracks in the rudder fitting – steering arm if memory serves me correctly - at the top of the rudder stock and which was attached to the steering via push rods.  Serious stuff and my discovery brought back many memories of the new rudder being fitted in the British Virgin Islands in 2008.  At the time the new rudder’s stock was ever so slightly smaller than the old one and so the old steering arm needed to be fitted accordingly.  At the time the ‘technician’ did this by belting the living daylights out of the (cast) fitting with a hammer until it eventually cracked.  Two weldings later and some shims had it all fitted okey.  Not.  Time had caught up with it and the steering arm had failed along the line of the weld.  So I decided, given our Atlantic crossing plans, it was time to fit a brand new one.
Cracked rudder steering arm
After some discussion in Baltimore & Annapolis at various yards, we hoofed it back to Deltaville, reasoning that they understood us and our boat.  Kindly they responded to our short time line (we really needed to get going on our crossing) where they measured the rudder stock precisely and a new fitting was ordered.  It’s interesting to note that Edson, the supplier, needed a reading that was accurate to within three thousandths of an inch.  On being given these dimensions they then bore the hole in the fitting.  It fitted perfectly and is still doing sterling service.
 
Hauling out at short notice
More Steering Breakages.  At this late stage we decided to sail south a relatively short distance to Norfolk, at the southern end of the Chesapeake Bay, and then head off for Europe from there.  The first night out, as you do, we had a fine gale which was quite unexpected.  We also lost autopilot steering when the cog, on the other end of the shaft that the steering wheel is fitted to, sheared so that the chain to the autopilot motor was completely disconnected. 

Unhappily, but not wanting to steer all the way across the Atlantic, we turned back to Norfolk, ordered a new replacement shaft, had the broken one repaired too, fitted the new shaft and autopilot chain, then headed north to New York City (again). 

As we had no further problems we then headed east for Europe via the Azores. As you do!
Some of the crew added their own modifications
which came with a drinks service too!

Saturday, December 7, 2013

Provisioning: On Reflection

On Reflection 

Good food & little celebrations are important moral boosters.  On our best and early days, we had steak and salads and on our worst, packet mashed potatoes stirred into tinned, rich soups with crackers.  We always had a “Happy Hour” (even better when we worked out how to make some ice!), which followed on from our “Herb Hour” (daily radio sched).  After Happy Hour, it was time for dinner then bed for the off-shift crew.  We had something fresh every day (usually fruit & vegies).  We found by eating regularly and well, we didn’t need too much in the way of snack food, although a coffee/tea and a plain sweet biscuit (granita) seemed to help the early morning watch survive.  So did the kit-kats!

Bubble wrapped glass jars survived; groceries held together well clustered in supermarket “green” produce bags and a large ham (wrapped in a vinegar soaked tea-towel) travelled well.  Eggs didn’t crush in their cartons and we chose packaged milk with a clip-down pouring spout to minimise spills.  Frozen mixed vegies taste infinitely better than tinned and creamed corn stirred into 2 minute noodles can taste like the real thing!  Baby cos lettuce are quite robust and pack into the fridge well (in Ziploc containers lined with paper towel).  A couple of butternut pumpkins, bags of potatoes, carrots and packet gravy mix made for an easy roast meal.  Oven bags kept the oven clean when roasting.  It seems that a little forethought goes a long way.

I still have a few things that make me wonder why I ever bought them; like dried Chinese mushrooms.  I also didn’t cook as much pasta as I had planned.  Why?  It requires a large pot of boiling water that can be quite dangerous in a seaway – even with an industrial rubber apron on!  I didn’t make cakes (package pre-mix) or spend hours baking bread.  We ate from bowls rather than plates and made much use of our large vacuum mugs, which kept coffee, soups, noodles etc hot.  Our fishing exploits remained empty threats and we were lucky that the weather treated us kindly, all things considered.  In all, we lived simply and well, arriving at Flores with little need to take on too many fresh provisions, only water.  We could wait until Horta with its larger supermarkets, filled with fresh foods and the pervasive aroma of Portugal – bacalhau – to replenish our dwindling supplies.

The constant motion plays havoc with your taste buds too and we arrived in the Azores with plenty of tins of beer, bladders of wine and even some chocolate leftover.... 

Our most useful things were without doubt, the WAECO, paper towel, fresh meat (frozen) and ice.  “Making life easy” awards go to Idahoan dried mash potatoes, 2 minute noodles, eggs and Progresso tinned soups.  And YES, I would provision again this way.

Friday, December 6, 2013

Provisioning: Bulging Bilges

Stocking the Larder

Supplies.  What is a good basic supply list?  Probably the best supply list we came across was in a Bahamas Cruising Guide which we’ve long since given away.  A tick and flick list covered all domestic supplies, including foods and this gave rise to thinking about soaps, shampoos, washing-up liquids and the like.  To some degree, quantities were “guesstimated” based on current home consumption, but it was always “one and a spare” at the very least.  Many of these supplies are seeing us well into another season but it is always better to have a little more than not enough – as I’m always being told!  Here’s a couple of list examples. A three month cruise & a few spreadsheet examples on the Cruisers Forum. 

Our Tastes.  What do you like to eat?  Food is very important at sea and dinner became a highlight of the each day for us.  So, we needed to consider foods we like, that are easy to prepare and nutritious.  I found it easy to consult a few favourite recipe books; the Australian Woman’s Weekly’s “Light & Lean” in particular.  Before you call me rude names, I generally use recipes as a starting point; once I have an idea in my head, I can easily create” my own versions.  I rarely make cakes but took along a few packets of flour so that if (absolutely) necessary, we could bake bread.  I had one packet cake mix & ready mix frosting for a birthday on board.

We like a hearty evening meal, take a light breakfast and will finish leftovers or have a “snack” lunch.  So, having chosen 30 or more main meals, I photocopied them, subjecting them to further scrutiny.   For instance, salads of cabbage, pumpkin or carrot would be perfect for the end of our trip when fresh supplies had run out.  Recipes were then pasted into an A5 diary, in day order, leaving room of course for breakfast & lunch ideas.  I used the back of the notebook to include notes on cakes, drinks, or even just good ideas.  (I am always subject to over-kill!).  This recipe book provided me with inspiration, a tempting picture and a list of ingredients that I knew I would have on board. 

We made some changes to our shop.  We were used to using long-life milk but still purchased a few tins of evaporated milk, a pack of powdered milk and a container of coffee mate.  We did the same with fruit, including fresh, dried and tinned.  I took what bread I could fit into the freezer, and a few rolls, then purchased vacuum sealed "wraps", rye biscuits and crackers.  Sadly, the only thing missing was a plentiful supply of cup-a-soup mix, clearly not to American tastes! 

Something else I started to do was date the tins.  What?  I found I still had tins rolling around from our Trinidad days, so took to them all with a large felt-tipped (permanent) marker.  On the top (the part I could see on bended knee), I wrote the year of purchase eg 10 for 2010.  That way I could easily see what was to be used up, especially as some of the older tins were starting to rust.  And that Vaseline or varnish thing didn’t do much for me.  We were going to be at sea maybe 30 days or so – not years or months - get a grip!  I also numbered the tins, eg 1/5 thinking this would help monitor usage, but that little exercise was a waste of time.  Sticking to a choice from the recipe book ensured there were always sufficient ingredients, tinned or otherwise!  WJ3 is quite dry, so I resisted the urge to label each tin with its contents too!

Ingredients.  Help me shop for all these goodies!  These recipes, further modified for sea journeys and minimal washing up, were then translated into quantities.  At best you could do up an excel spread sheet or at worst a sticky note tally, but in the end, you will have your quantities; specific, useful foods, not supplies that you don’t have a clue what to do with!   
 
There is no time to dither about what to prepare when underway.  We added to our list an almost trafficable quantity of kit-kats, enough tonic/lemon for a daily happy hour tipple, catering sized tubs of mixed nuts and tubes of Pringles – the only thing that placates a sea-sick prone tummy.  
 
Buy all your long-life supplies first, then finally it’s off to the supermarket or farm produce stall to make your fresh produce selections. The fresher the longer it keeps. 

Thursday, December 5, 2013

Provisioning: It's ALL in the Planning

Sorting the Basics

We've been asked (yes, really!) how we went about provisioning for our jaunt across the Atlantic.  As a blue-water novice, let me tell you, planning to feed us on what was to be a bumpy journey inclined at 45 degrees for 30 days or more, took a bit of research.  Not to mention quite a few trips to the supermarket in Deltaville Marina’s “loaner” car.

Research.  What advice can experienced sailors give me?  The internet and many a sailor’s blog gave me insight into what had worked for them.  Some preferred tinned food, others dried; vegetable life expectancy was frequently discussed, as was the value of reliable refrigeration.  Vegetarian meals were whipped up in a flash and freshly caught fish cutlets sustained many a hard working crew.  “We could grow our own herbs, sprout beans and coddle yoghurt,” GS enthused.  Sure!

Planning.  What are the passage basics?  Planning was important though, so we thought we should start with a few basic facts.  How long would said passage take us, how many crew were going, what do we like to eat, what capacity did we have to store foods, and what was the weather going to be like (in a general sense).  No point in trying to bake custard or set jelly if you’re healed over.

Now having some idea of Windjammer’s average speed, we calculated distances from Chesapeake to the Azores and then on to Lisbon.  So, at worst case, we determined that it would take us 30 days to get to Flores and then 10 days to Lisbon from San Miguel.  Reasoning that everyone eats, we knew we would find some fresh supplies in Horta (and also on the other Islands as we cruised by).  We hoped, contrary to our dismal fishing record to date, that we would also snag a nice tuna or wahoo. (We never did…)

Equipment.  How do you like to eat and cook?  At the Annapolis Boat Show, we had, (hang the expense) shouted ourselves a stainless pressure cooker.  “That,” said the Captain, “will be your most useful tool.”  Actually, it wasn’t – just in case you stop reading here and rush out to buy one!  I love my wok and that, with a large frying pan, and a few stainless saucepans (with lids) did us proud.  I think it’s also a matter of what you are used to cooking with too, although high sides are very important.  I purchased a heavy duty rubberised apron and silicon oven mits – it’s so easy to tip boiling water or hot foods over yourself in choppy seas.  On that note, I would never ever deep fry anything at sea…that oil is an accident waiting to happen. 

While you are raising your eyebrows with concern over our excessive “washing up” requirements, this too was modified with a bucket to fit into our sink to store dirty dishes for one large wash a day.  We fixed a dish drainer to the sink with “occy” straps and only once or twice did the dripping contents tip into our shoe bin.  We did try using sea water to wash up but salt encrusted everything (and became damp).  Cheap stainless bowls and cutlery started to rust and I had to start throwing out cooking utensils which disintegrated before my eyes. 

Washing up brings to mind water usage and after some consideration, we decided that our 200 gallons of fresh water would last – we would make it with careful use – as at worst, in the Caribbean, we had to resupply after 3 weeks (with 3 on board swimming daily).  We also carried extra jerry cans of water (and fuel) as emergency supplies, strapped to the deck.  We never needed it!  (But we would always carry reserves.)

Stowage.  Where will I put all this stuff?  Stowage was another issue, and initially, the plan had been to store groceries under the forward bunk.  After struggling with an unyielding mattress (and having to remake the bed each time– and this was all in our very sheltered marina berth), it became apparent that lockers under the settee would be easier to get to.  Everyday items and those in use (opened) were kept in the galley, the refrigerator became a storage vat for perishables, the freezer (as it didn’t work terribly well with a few generator bursts each day) held our cold drinks and the WAECO was put into service as a freezer (on solar panel power).  Tins were stacked into crates and placed in the galley floor locker.  Glass packaged items, regularly accessed dried goods (like rice & pasta) and those in paper or cardboard wrappings would go behind the settee.  All “re-supply” goods then, were to be stashed into lockers under the settee.  We purchased a few small plastic crates (screwed into place) to hold loose items.  Their high sides meant that we would not lose too much in the event of a knock-down.  Yes, we had to plan on worst case scenario weather too!

Lastly, we had to think about packaging.  Easy to dispose when the garbo comes each week, but at sea we didn’t want storage areas to be full of smelly garbage or cockroach eggs hatching from cardboard containers.  So to minimise packaging, as many items as possible were placed into resealable Ziploc bags.  GS was also lucky to find, in Wal-Mart, a small, vacuum storage system; essentially resealable plastic bags with a manual pump.  Meats and cheeses etc could be removed from trays, then vacuum sealed in serving sizes, contents noted with a permanent texta and frozen to last the journey.  Everything that went into the big fridge was repackaged into the Ziploc containers (replaceable plastic containers with a decent sealing lid) of various sizes, all lined with paper towel. 

One other ah-ha moment was when we realised how much food is already in vacuum sealed packaging.  This was particularly useful as some items did not need to be refrigerated or frozen eg salami.  Lots to think about and we hadn’t even bought any foods yet!