Showing posts with label outboard. Show all posts
Showing posts with label outboard. Show all posts

Friday, July 19, 2024

2023: Outboards. Reliably Unreliable?

 Yamaha Outboard

Our faithful Yamaha worked fine and I was ever so proud of myself since I had made repairs the previous year and saved myself at least USD 3000.  That is until we got to Vero Beach in Florida when it would not cooperate and kept cutting out, or would power up only to die shortly after.  And then it wouldn’t start.  And we had only a few days before our guests arrived from Oz.  Talk about Murphy’s Law!

New Mercury 6hp 4 Stroke Outboard

So, rather than lose time working on, and may be repairing the Yamaha, we decided to get a new one, quickly.   A phone call or two and we had ordered a new 6hp 4 stroke Mercury available in the North Palm Beach store.  We could anchor a few kilometres near by and a kindly cruiser anchored near to me gave me a tow to the dinghy landing up a creek and the only place you could park a dinghy in that area.  I walked to West Marine and, against all their rules apparently, gave me and my new ob a lift back to the dinghy.  Off drove my friendly WM and I proceeded to fit my new Mercury to Bruce.  Only it wouldn’t start!  And, yes, I had fuel in the tank and it came with {a minimal amount of] sump oil.  Anyway, a friendly dinghy happened to be leaving the landing area and he and his family kindly gave me a tow back to WJ3.  Thank goodness for the boating community’s sense of helping each other in times of need...

The next day, after studying the Owners Manual umpteenth times and following the startup instructions, it still would not start.  So I called WM and they advised me that it was now out of their hands and I needed to discuss my problem with a dealer, which they were not.  WM just sell the stuff apparently.  And when I talked to a recommended ‘dealer’ they wanted me to deliver the ob with the appropriate paperwork.  And their work would have to be fitted in with all their other commitments, so nothing was going to happen quickly.

by now, our guests were sitting on a dock in West Palm Beach!  Oh well, nothing to lose, so I set the throttle on full power (not recommended) and pulled the starting chord.  BROOM.  All good.  I called WM and told them I had fixed it and how, and they were happy.  I was very happy and off we went.  Our guests, by this stage fuelled with a few happy-hour G&T's (American cocktail size), were very happy!

Four months later the Mercury started playing up (single cylinder remember) and a new spark plug fixed the problem.  Our Yamaha has had two changes of spark plugs in 15 years so I am now wondering if that might be the problem with that motor.  Anyway, the Yammy is now with a mechanic in Trinidad and, if they fix it as I expect they will, I will then have two ob.  Just like the alternator, it’s always handy to have a spare.

I later purchased, in St Martin, a throttle control variable tiller extension arm and it works a treat.  Even though the 6hp outboard can only comfortably move us through the water, when I am by myself and sitting forward, the RIB will comfortably plane.  I remove the extension when more than one person is on board.


Sunday, July 14, 2024

2022: Outboards - Not for the Faint-hearted

Outboard 15 HP Yamaha.

In 2019 my outboard (ob) had developed a water leak from the area where the engine housing and the upper casing joined.  I was able to continue to use it all 2019 but only at slow speeds.  A local mechanic checked it out and told me what was wrong but he was busy and said I could do it myself, which would save me a lot of money.  

Okey then.  I tried to separate the two parts by removing six bolts but couldn’t do it – they appeared to be stuck together.  Forever!  I checked with a local ob business hoping for some friendly hints only to be told nothing helpful except that I should purchase a new ob as, they said, if they tried to repair,  it would involve a lot of work (echoing the previous assessment) and cost so much so just get another (new) one.  Only around USD 3000+ (AUD 4500) so why not.  Also the ob is 23 years old so, you know, you’ve had a good run.  

I slept on it that night (mostly awake) and decided to give it another shot the next day and, if I broke things, what the heck anyway.

What I tried was to insert a metal rod into the bolt holes of the upper casing and gently tap them with a sledge hammer working my way around all the holes one by one.  I did this over an hour or two without success until I inserted a small crow bar and levered the engine off the cowling.  Voila.

I had to replace the gasket and did so with a new one.  The challenge was to match my model number (British Virgin Islands) with US models and there are/were several models numbers for the same engine.  The local ob shop kindly did this and the new one fitted perfectly.  

The actual fault causing the water leakage was from a crack in a bend at the top of the copper tube joining the upper cowling with the water pump in the lower cowling.  This was not available at the time in the US so I purchased some copper tubing at the local hardware store and made my own.  It fitted very well and, when I put everything back together again, it worked well pumping water with no leaks.  I might add that I practised bending copper tube on some scrap metal I found in the boatyard before bending the final piece and fitting it to the ob.  Worthwhile, as you really only have one chance to make this right angle bend, so you need to get it right.

Outboard Propshaft Seals

I decided to change these, as I thought there was a small leak.  But first, some education - by looking at a bunch of very helpful YouTube videos, then choosing the simplest way I thought possible.  I removed the prop and spacer then drilled holes into the seals making every effort to avoid touching/scratching the prop shaft (as every video made a big deal of this!).  I then used small hook tools to extract each of the seals.  They came out quite easily.  I then replaced them with new ones using a PVC pipe, and used a hammer to insert them.  All seemed to work when I filled the gearbox and ran the motor in gear later on.  

Isn't it marvellous what a bit of self-help and lots of really nice people posting useful guidance on YouTube can do for you! And our 23 year old motor has a new lease on life too!


Thursday, November 15, 2018

2016: Run for Cover...

The anchoring field was busy in June
The plan for this year was to cover Italy and Malta.  First stops were ports we missed on our 2015 “round the Adriatic tour”, then cross to Malta, head up to Sicily and finally meander up the Italian west coast taking time to hit all THE tourist spots.  Haul out decisions would be made on the fly; hoping for somewhere along the French or Spanish coast.  Big plans and bigger problem - namely our limiting 90 day visa!  We’ve moaned about this before on the WJ3 blog but the difference with the middle section of the Med is that there is nowhere “close” to run and hide.  

Greece:
2016 began with the usual boatyard chores in Aktio - two weeks of hard slog, but who can deny it's a pleasant life.  WJ3 was treated to a professional polishing, the shower sump was unblocked, the anchor line replaced, rusty bicycles serviced and bow thruster batteries sorted out (they had not charged in our absence).  We needed an electrician to sort the battery issue out.  Finally, WJ3’s rigging was inspected – an insurance requirement.

Aktio in Preveza - a great place to haul your boat
On splashing, the engine started…that was good, but the generator again chose to be obstinate.  Hmmm, something to look at whilst on anchor, we thought.  Launching Bruce (the dinghy) too was something of a concern as the outboard stubbornly refused to function and more alarmingly, began to fill with water.  Drat!  Someone had stolen our dinghy bung – and of course, it’s a US fitting in an EU world.  To add to post-launch miseries, the bow thruster continued to be obstinate, crying out for even more professional help.  So there we sat, afloat with not much working.  Sound familiar?

Within a day of splashing, we moved into the Preveza Marina and so our precious Visa Days ticked by whilst we attended to:

Generator Coolant Pump.  It was leaking and I wasn't sure how to remove it as it's part of the engine, not a separate item like the saltwater pump.  I had a local German mechanic look at it (we’d used him before) and, on inspection, he pronounced it dead.  It was badly corroded and needed to be replaced with a new one.  This was at the start of the season at Preveza, Greece, and so we had to wait three weeks for the replacement part to be quoted, ordered and then delivered – from the US of course.  It took about an hour to put the pump on.  The generator ran fine thereafter.  I won’t mention the cost except to say that it was enormous, even the mechanic was embarrassed to tell us.

Time for a last swim at Jumping Fish Bay
Outboard Motor Not Starting.  Again, right at the start of the season, the outboard wouldn’t start, even though all was working fine at the end of the season when I run it until the carburetor ran out of fuel.  In hindsight, I should have run it in the yard before launching, but didn’t; an oversight on my part.  Anyway, after trying for some time I pulled the carburetor apart and inspected it for cleanliness.  It looked clean, but after I put it back on, it still wouldn’t start.  A kindly fellow on a nearby boat came over in his dinghy and freely offered advice, but despite his remedies, it still would not start.  Time for some searching on the web!  One useful piece of advice was that “a clean looking carbie does not necessarily mean it IS clean”.  This YouTuber advised to clean it to be sure, especially by inserting a thin wire into every orifice possible.  Well, I did this and the outboard started just fine.  So, big lesson here is that just because a carbie looks clean doesn’t mean it is and so do what I eventually did.  I’ll freely admit I did not see anything suspicious as I prodded and probed with my fine piece of wire.
  
Refrigerator Re-gassing.  Ahhh, yet again we had to have the refrigerator motor/evaporator re-gassed with the unusual hard-to-locate gas required for our Grunert 110 volt fridge.  Our reliable mechanic, although licenced, was not available so we contacted a local guy recommended by the marina.  Short story is he tried to rip us off by quoting and then trying to raise the price on the day.  Also, he tried to convince us to do more modifications than necessary.  Anyway, the fridge worked once it was re-gassed.  This little episode, apart from expensive now annual re-gassings, prompted much discussion on “a better way” to refrigerate given that our little WAECO battler was working brilliantly and running diligently on 12 volt sunshine power.

AIS.  We had purchased a GME AIST 120 and I fitted it next to the chart table, connected to our laptop via the program CD that came with it, and yet another antenna was fitted to the pushpit.  It works okey but we have since passed a number of ships at quite close range and there has been no signal received from them at all.  I certainly would not rely on it. 

There's more to follow....

Sad to be leaving our favourite Taverna over near Aktio

Sunday, February 28, 2016

2015: In the Marina & Loving It

Preveza Marina continued (Part 2):

Generator Coolant Water Pump.  The generator has a coolant system that you fill with antifreeze and this keeps the insides of the important bits of the engine cool.  Keeping the coolant cool is the job of the raw water that is circulated around the engine and spat out with the exhaust.  Well, this time it was the coolant water pump’s turn to fail.  Shortly after we set off on our trip north for Croatia there was clearly a major leak and gathering in the drip tray was all this coolant.  We returned to Preveza where our new best friend Stefan soon diagnosed the problem as being a failed coolant water pump ie it had corroded through its casing.  I thought that’s what the antifreeze coolant was supposed to stop.   Two weeks later, we had a new spare pump and fitted, at a modest cost that I still grit my teeth over – US parts imported into Europe means BIG money, mostly taxes.
This folks is what caused all the teeth gnashing, many weeks delay
and almost broke the annual cruising budget!!
Masthead Anchor Light.  This was working perfectly when we tested it shortly after we returned to the boat this year.  Once on anchor, however, we found it would not work, or would eventually.  After a trip up the mast to check the fitting and globe, when it seemed to work properly after some fiddling and testing, we then found that it would flash regularly rather than remain constant when turned on.  I still have no idea why it flashes but we just left it – it made it so very easy to identify our boat when returning to the anchorage at night time!  I might add, for all of you that are tut tutting, there are any number of combinations of anchor lights around Europe eg flashing single and multiple red and/or white lights at mastheads, in cockpits, tiny cheap solar lights that you can hardly see (especially when near a town with all their lights showing), and many boats without any anchor light at all.
There'll be a few more folks in town shopping today
Bike Repairs.  Our folding bikes are indispensable.  I’m surprised to see so many cruisers walking to/from/around town when they could be biking it.  Ours needed a service and a local Greek bike shop owner in Preveza did a wonderful job of restoring (read replacing) our fancy Shimano gears and generally fixing the bikes back to almost new.  We also lashed out and purchased some helmets.  The shop was a referral through Aktio.
Outboard Safety/Cut Off Switch.  Our Yamaha switch had given up the ghost some time ago although it would cut off when you pulled the clamp from the ignition.  Eventually it wouldn’t do that so I had to disconnect the switch, let it hang down and then use a coin or copper washer to make the electrical contact that would turn it off.  Tried to get a switch in Greece but not possible apparently.  Will get one in Oz and take it back overseas in 2016.
Ruins always seem conveniently located in Greece.
This is Nikopolis, Augustus's celebratory city just outside Preveza

Saturday, January 30, 2016

2014: Repairs Underway in Poros

Poros, Greece

Raw water inlet hose on engine started to leak, just a few drops every minute.  I hate water inside the boat at the best of times so, having found the leak by feel, I bound it with some very stretchy tape that I carry on board which is designed for just this sort of eventuality.  It stretches about four to five times (I’m guessing) its original size and you wrap it around whatever you want – it sticks to itself if you don’t ruin the sticky part with grubby fingers.  I also wrapped some duct tape over that and it stopped leaking for the rest of the season. 
We had a great trip north up the Turkish coast from Marmaris, with some
isolated anchorages, clear waters perfect for snorkelling and amazing
ruins (like Pergamum) to explore along the way.  Highly recommended!
Continuous Furling Line for the Mainsail.  It needed replacement I thought as it was looking a bit hows-your-father.  Tried at the Marmaris marina boatyard sailmaker but, by now, we weren’t talking to each other so no luck there.  Tried other contacts but, although promising to get back to me, didn’t.  At this stage we were on anchor just off the Marmaris boatyard and, I have to admit, I sensed  a lack of enthusiasm by tradies to work on boats when at anchor (perhaps they worry about getting paid before boaties sail away in the night).  So, we gave up trying and departed Marmaris still with the original line and it lasted fine (for quite some weeks) until reaching the west coast of Greece and about to enter Poros, with a good wind blowing.  I started to furl the mainsail, probably under a fair bit of pressure but not as much as we’ve experienced before, then, bang, the line snapped.   I simply furled the main using a winch handle on the winch on the mast. 

In Poros there is a popular chandlery and the staff there were very helpful, selling me some new line and also arranging for someone to come out the next day to do the splice.  I might add here that the furling line is braided, this splice has to be pretty much exactly the same diameter as the line is so it will easily run through a bunch of blocks and winches, while at the same time be almost as strong as the line itself. 


The one that got away!
We had arranged that I would meet the ‘splicer’ the next morning and take him to and from the boat, which was on anchor.  The chandlery man very kindly came along to the pickup point to make introductions and off we went.  The ‘splicer’ was a local, in his late seventies, couldn’t speak English and had a gammy leg (at least one of them).  On arrival at Windjammer he almost fell into the water as he endeavoured to cross from the dinghy to the boat at the stern (it doesn’t get friendlier than this let me tell you) and all crew had to come to the rescue – it was a near run thing.  

Unperturbed he set about his business and nothing I could say would influence him as he went about his task.  Anyway, after an hour of honest toil I had a splice that did indeed slide through all the sheaves and winches but with about 5% strength.  We all agreed that it was a fine effort and I duly returned him to shore, paid him the agreed amount plus a healthy tip, and we parted on very good terms.
We had spectacular scenery through Greece too. 
This is Cape Sounion.
I now did what I wanted to do in the first place – do it myself.  I had watched YouTube for ‘how to’ instructions several times and also had written instructions to refer to.  It was a fairly easy fix by following the instructions.  The hardest bit was the three splices you have to stitch in place to hold the joins neatly and securely together – it took me two goes to do a neat job ie making sure the rope’s diameter was not increased so it easily moved through blocks and jammers.  Very satisfying effort in the end!  Why didn’t I do it myself in the first place?  Well, I thought that for such an important repair I would watch an expert do it first, then do it myself next time.  Oh well, he was a lovely old bloke and it was one of those magical experiences you only get when boating.  We also think he’s dined out a few times with his mates on the strength of his “near death” experience on our sailboat.   In 2015, when the rig was checked by professional riggers for insurance, they noted that the furling line is too stretchy and too large so I may replace it next year.
Outboard Doesn’t Go Fast When Powered Up.  In Poros, one night we headed into shore for dinner and since we were anchored a fair distance from the town docks we sped into town at best speed on the plane.   Our 15hp RIB dinghy ‘Bruce’ can tow a skier.  On the way back to the boat we motored along fine but when trying to get onto the plane the engine would rev madly but not have the "umph" to get the boat going on to the plane.   We could still use the dinghy but only at slow speeds.  I checked the prop and it seemed to be locked in ok and couldn’t find any fault with the gear box.  When we eventually got to Preveza the first time to check out the boatyard, we gave the motor to the mechanic arranged by the Aktio Marina.  The mechanic took the outboard away and next day it was back with a new propeller fitted.  Seems that the old prop had worn its gearing so badly that it slipped on the gear shaft at high revs.  So, there you go, I certainly didn’t think of that.
Poros is the quintessential Greek island village