Showing posts with label mechanical. Show all posts
Showing posts with label mechanical. Show all posts

Wednesday, July 17, 2024

2023: Back to a Cruising Life

Catching up at last: 2023

The Galley Slave and I rejoined the boat in Deltaville VA, Feb23 and cruised to Trinidad.  Along the way we experienced ongoing problems with the electrical charging system, amongst other things.  Quite the maintenance list, actually!

RIB Puncture

Bruce, our faithful RIB, had developed a leak in one compartment (port aft) and looked decidedly deflated when I rejoined the boat.  I tried to find the leak using a soap and water mix, several times with brush and spray, but could detect no bubbles.  It wasn’t until I launched WJ3 and Bruce that I was able to detect bubbles streaming up through the water from the leak.  It was an old repair gone bad and not small.

I pulled Bruce from the water onto the marina pontoon dock, turned it over, washed with fresh water, deflated the respective compartment, sanded and cleaned, and then glued a patch over the leak.  I carry spare fabric on board courtesy of a fellow sailor whose Hypalon inflatable had been written off.  

 I used West System G/flex thickened epoxy adhesive based on the advice of the local hardware and it has worked perfectly so far.  There was no Hypalon adhesive available locally in Deltaville.  You need to ensure that there is plenty of pressure and I used diving weights for this plus clamps.

Dripless Shaft Seal

On launching at Deltaville Boatyard the DSS wasn’t dripless, leaking a small amount.  The travel lift operator kindly assessed the problem and, with the help of a small sledge hammer, stopped the leak.  I think he just tapped the aft ‘bracket’ forward a bit to tighten the whole thing up and all is good.  I have never before had any problem and the DSS has been on the boat since I purchased it 17 years previously.

Whisker Pole

I wanted a whisker pole for the staysail when running dead downwind and I saw one on the side of the road among a pile of other boating junk.  I knew the owner (old Bob) and, after asking him if he wanted it to sell it to me, he gave it to me.  One end was a normal piston type end fitting and I wanted the same for the other end, which was some other useless fitting for my purposes.  I happened to have a spare spin pole end fitting and, after having it machined to fit my new pole, fitted perfectly.  I then found a 2nd hand slider fitting for the spinnaker pole track, purchased a locking slider and now all done, almost.  I now need to fit a block on the front of the mast and a topping lift.  All up it will have cost about $150.

I might also think about using this pole, which is pretty substantial, for a bowsprit for my asymmetrical top-down spinnaker furler.  We’ll see.

Fridges Not Refrigerating Properly

Shortly after leaving Deltaville and on our way southwards along the ICW our fridge and freezer were not getting really cold enough.  Yes, cold-ish but not like they normally should perform.  I checked most things but could not identify the problem: all lights were on that should have been on but the water pump wasn’t operating.  I checked for any blockages in the plumbing, electrical cabling and connections and even pulled the pump apart (as much as I could).  Finally, I checked the manuals and I noted the mention of a fuse in the control box.  I checked it and, sure enough, it had failed.  I replaced it and all good, both boxes cooled down as per normal in double quick time.  The lesson here is that, although all lights were on, not everything was working properly, clearly.  I just simply thought that if all lights were on then everything electrical must be working – wrong.  You never stop learning.

WAECO Fridge/Freezer

To add to this dilemma, our ever faithful WAECO fridge/freezer, purchased in 2010, decided to play up and finally died in 2023 after 15 faithful years of service.  Our built-in fridge and freezer can only be run when the boat is in the water as, to keep them cool, sea water has to flow around the compressors when they are running.  On land, which is a fair amount of time at the start and end of each season, we use the WAECO as a fridge and/or a freezer.  It’s mostly been a reliable companion, trusted importantly, with keeping our cold beers and food fresh.  The WAECO unit has been just great and we loved it.

However, rather than try to live with an old but unreliable friend, we ditched it and purchased another and, since we had friends about to join us in Florida, there wasn’t time to muck around.  Our new one is virtually the same as the old – a 50 litre Dometic portable fridge/freezer purchased from Fort Pierce West Marine as we made our way south along the Intra Coastal Waterway towards Florida.  She works just great and so we are very happy.  I should add that Fort Pierce Marina kindly let us hang off a dock while we jumped an Uber to West Marine to pick up our purchase.  Very friendly staff given that it was peak migration time for boaters heading north and not much room.  A nice marina experience.

 E-Bicycle

We purchased an Ancheer 20” folding electric bike to replace our folding bike stolen in Annapolis in 2019 (from a shop just opposite the local Police Station - as GS likes to remind me!).  It, like all e bikes, is comparatively heavy but, for my ageing body, is oh so easy to use.  It speeds along with very little effort and we have also fitted ‘saddles’ to make it a useful pack horse for trips to super markets etc.  One reason we went for this particular model (there seem to be 100s to choose from) was the aluminium ‘spokes’, disc brakes, and reviews it had received.  So far, we are very pleased with it.  

We also purchased stowage bags and have put four mounting brackets on the coachhouse roof so that we can tie it down with ratchet straps.  When sailing we also cover it loosely with the foredeck sunbrella awning and, after four months of sailing south through the Caribbean the bikes were in really good condition.  I also have upgraded the bike security locks and use them always.

 


Monday, February 18, 2019

2017 & 2018: Bless Those Batteries

Ongoing Saga: #11

Solar Panel Regulator, New House Batteries and New Smart Regulator for Alternator.

This was the beginning of a long drawn out and rather expensive saga over a period of nine months.  Sopromar Boatyard in Portugal were asked if they could come up with some charging solution for my three sets of batteries while I was away back home – a single 12 volt starting battery, four 6 volt house batteries and 2 bow thruster batteries.  In the numerous exchange of emails over several months the result was that there wasn’t a solution.  Meanwhile the regulator for the solar panels had malfunctioned, needed replacing and that subsequently the four house batteries had gone flat and needed to be replaced, which they duly did ie solar regulator and batteries.  The old batteries were almost 10 years old – a ‘Trojan’ performance, so probably time for new ones.

At the same time I also had the alternator checked out and we identified that we needed a new regulator for it, which I purchased separately and brought back over with me when I returned to the boat in mid Aug17.  Sopromar fitted the new regulator, tested it and that was that.  Or so we thought.

The bow thruster batteries are AGM and so had held up fairly well and the techo had wired them up somehow so that they received a trickle charge of some sort from the solar panels and didn’t flatten.  AGM batteries can fairly happily sit for up to around six months without any charging and not suffer I’m reliably informed.  

Anyway, to cut a long story short the new regulator was not wired correctly and so the batteries steadily drained once we got underway, except for some charge from the solar panels (which only charge the house batteries and starter battery).  The bow thruster battery charging only occurs when running the motor/alternator.  To add to this mix, we had a generator that didn’t work.

Our batteries were recharged on shore power whilst ever we were in marinas at Lagos, Madeira, Canary Islands and then Cape Verde Islands.  In between were relatively short trips so I wasn’t too concerned as the solar panels did their thing outstandingly and I rarely used the bow thruster.  It was on the 16 day Atlantic crossing that I became fully aware of the charging problem as the starter battery voltage in particular dropped significantly, although I was always able to start the engine when I had to.  

On arrival in Antigua (where we anchored) I had an electrician look at the charging system and he thought it was all okey, particularly when his meter showed 12.6 volts (not the 13 – 14 volts necessary) and he thought the regulator was doing what it should.  He also condemned the house batteries as needing replacement even though they were less than 12 months old.  

No point arguing, so we pushed onto Sint Maarten, initially on anchor but later on shore power at FKG Rigging, where I was able to charge the batteries using shore power.  I also had the house batteries charged and tested at Budget Marine where they were announced as being in good condition.


Next stop was Turks Caicos (shore power in the marina) where another electrician, a friendly French Canadian, made a valiant effort to identify the problem of a very low charge and suggested that the regulator was faulty, only achieving ‘float’ voltage instead of starting with ‘bulk’ and moving through ‘absorption’ and then onto ‘float’.  He also had access to the regulator manual and spoke to the manufacturers but thought it was wired correctly.

We entered the US at West Palm Beach, Florida and then proceeded north along the Intracoastal Waterway anchoring most nights - happily for as long as we had sunny weather.  Unfortunately, further problems were experienced when we had a succession of overcast days and the batteries received very little solar power.   We then experienced some difficulty when anchoring off New Smyrna Beach using the electric anchor winch.  The starter battery was quite sick by now so, with Daytona in our sights, we kept the engine running all night, pulled the anchor up by hand the next morning (thankfully it was clean sand), and made for Daytona Beach.

We berthed in Halifax Harbour Marina (great people and very friendly fellow boaties).  I tried to charge the starter battery using shore power but it would not hold a decent  charge so I had to purchase a new one.  I also consulted with a trusted electrician who had done some work on the boat about 9 years previously after the mast had been hit by lightning.  He is semi-retired now and advised that I should do it myself – every good captain should know how to set up a regulator he said - so read the manual at least three times – and then do what you need to.   I followed his sound advice and found that the regulator was wrongly wired, wired it correctly myself, and now all batteries are charging pretty efficiently, although I sometimes wonder if the starter battery should not be getting a bit more charge.

In summary, three electricians couldn’t get it right, but the fourth electrician gave me best support of all – do it yourself.  Lesson learned, big time.



Sunday, February 17, 2019

2017 & 2018: Oh NO! Not the Generator...

Ongoing Saga: #10

Generator Not Starting and Fuel Line Fitting in Canary Islands
.  
In Portugal the diesel generator had been sitting for 9 months and wouldn’t start for reasons I could not understand, so I had a mechanic look at it – several as it turned out.  They replaced the gasket for the cover over the valves, checked valve clearances, adjusted them and eventually they started it and we ran it several times.  Great.  They did not think the injectors needed attention as ‘it runs so well’.  Anyway, off we went and it NEVER started again.  

When in the Canary Islands I discovered, while trying to start the generator, that a bleed valve over the fuel line was not seating properly as the thread would not allow full tightening.  Ah ha!  I thought, this must be the problem – allowing air into the fuel lines – a definite no no.  Fortunately, a visit to one of the marina chandleries proved fruitful and the very helpful gentleman there found a suitable fitting somewhere out the back of the shop which matched my fitting.   It cost next to nothing too and I was so grateful.  Even so, the generator would still not start.

I had two other mechanics check the generator over for me – in Antigua and then Sint Maarten – and they could not start it.  We didn't have time to wait in the Turks Caicos (the weather was a bit iffy) or I would have had a mechanic go over it there too.  The motor turns over fine but just won’t start.  

The consequences of course made themselves clear as we moved along the Atlantic ICW (US coast) where we anchored out rather than hooking up to electrics at marinas.  See comments on batteries.  The plan is to have our very sad generator checked out again when I'm back in the USA.  Another job for next year...


Monday, February 4, 2019

2017 & 2018: Gourmet Galley

Ongoing Saga: # 4

Tap Washers
.  
My US tap washers are really strange having two O rings each and, of course, they weren’t available in the EU.  Hopefully I can get replacements when I'm back in the US and will be able stop the odd leaking tap.

New Stove.  Our Force 10 stove was around 17 years old.  It expertly blackened the bottom of pans, had to be started using a lighter (silly AA battery self starter had never worked since we purchased the boat), the oven was super-slow to cook, and the Galley Slave (GS) was understandably Not Happy.  

So, I did some research, talked to fellow boaties in the yard, consulted GS when I had a short list and we decided on a Dometic three burner, with grill and oven.  It’s a bit smaller than the old Force 10 so easily fitted into the recess.  It is also wired to the boat’s electrical system rather than needing AA batteries so it's easy to start and came with a set of brackets to hold pans on the stove in a seaway.  

Being a European design, the gas fittings had to be modified a bit.  I retained the US flexible gas line, had a fitting soldered to the stove inlet fitting by Sopromar, and then used a ‘modified’ brass hose joiner to make the connection.  I also installed a gas detector at the bottom of the stove which is also hard wired into the boat’s electrical system.  Whenever I turn on the ‘gas’ at the switchboard the gas detector also activates.  The stove works a treat, no blackening and best of all, the oven works efficiently.  Happy GS and so even happier Captain.

All the bells & whistles for our Galley Slave
Barbecue Mounts.  The barbecue was sitting somewhat askew on the pushpit mounting and needed more support than the standard Magma fitting I had purchased and fitted years earlier.  The standard fitting to attach a barbecue to the horizontal pushpit railing was simply not up to the task because the barbecue is not light and needs substantial support.  I attached two upright struts to the base of the barbecue mount and then to a vertical piece of the pushpit utilizing standard 1” joiners for stainless tube.  The barbie now sits securely, looks much better and is better to cook on ie it's now horizontal and your sausages & chops don't roll overboard if the weather gets a bit rough. 

Friday, December 14, 2018

2017 & 2018: For the Love of Engines

Ongoing Saga: # 2

Engine Exhaust Elbow and Exhaust Hose.  Another observation in the 2016 survey report recommended that an inspection of the engine exhaust elbow be conducted.  A Sopromar mechanic was engaged, removed the elbow inspected, pronounced all good, but meanwhile he identified that the exhaust hose from the elbow to the muffler needed replacing.  He did so but it took him a long time as it was very difficult to remove and to put in a new length as there was a bulkhead in the way and the hose is heavy duty steel reinforced rubber.  Has functioned flawlessly since.

Engine Exhaust Muffler.  On testing the new hose the muffler was found to be leaking at the bottom where it had been sitting against the bare fiberglass of the hull.  It’s surprising it hadn’t started to leak a long time ago.  The muffler was removed and, since it’s fiberglass, was repaired by the yard’s fiberglass techo.  He did a great job, not only repairing the known crack but one or two others that he identified.  He also glued rubber strips to the bottom so that no longer will fiberglass be sitting against fiberglass, constantly rubbing together whenever the engine is run.  He also painted it so that it looked like a brand new one.

Fresh Water Flusher for Engine's Water Intakes.  I purchased and used several times a fresh water flusher, something I could manage myself, for use when the boat is out of the water.  The flusher is a standard purchase and it looks like an enormous ‘plumber’s mate that you use for unblocking drains or your toilet.  Its mounted on some block of wood etc on the ground with the flush fitting covering the thru-hull fitting eg engine water intake.  You then attach a hose to the flush fitting and the other end to a tap.  When you start your engine you immediately turn on the tap and run the engine with the water intake more or less as normal. 

I set up the hose so that I could do it myself on board by running the hose from the tap into a on/off valve in the cockpit then over the side to the flush fitting.  I start by closing the valve, then I turn on the tap, get back on board, start the engine, then open the valve, then check exhaust for water coming out.  Before turning off the engine, I turn off the valve first, turn off engine after a short pause as water still keeps coming out the exhaust for some short time.  I then turn off the tap. Love it.
An exciting view of a flushing engine...hmmm!

Thursday, November 15, 2018

2016: Run for Cover...

The anchoring field was busy in June
The plan for this year was to cover Italy and Malta.  First stops were ports we missed on our 2015 “round the Adriatic tour”, then cross to Malta, head up to Sicily and finally meander up the Italian west coast taking time to hit all THE tourist spots.  Haul out decisions would be made on the fly; hoping for somewhere along the French or Spanish coast.  Big plans and bigger problem - namely our limiting 90 day visa!  We’ve moaned about this before on the WJ3 blog but the difference with the middle section of the Med is that there is nowhere “close” to run and hide.  

Greece:
2016 began with the usual boatyard chores in Aktio - two weeks of hard slog, but who can deny it's a pleasant life.  WJ3 was treated to a professional polishing, the shower sump was unblocked, the anchor line replaced, rusty bicycles serviced and bow thruster batteries sorted out (they had not charged in our absence).  We needed an electrician to sort the battery issue out.  Finally, WJ3’s rigging was inspected – an insurance requirement.

Aktio in Preveza - a great place to haul your boat
On splashing, the engine started…that was good, but the generator again chose to be obstinate.  Hmmm, something to look at whilst on anchor, we thought.  Launching Bruce (the dinghy) too was something of a concern as the outboard stubbornly refused to function and more alarmingly, began to fill with water.  Drat!  Someone had stolen our dinghy bung – and of course, it’s a US fitting in an EU world.  To add to post-launch miseries, the bow thruster continued to be obstinate, crying out for even more professional help.  So there we sat, afloat with not much working.  Sound familiar?

Within a day of splashing, we moved into the Preveza Marina and so our precious Visa Days ticked by whilst we attended to:

Generator Coolant Pump.  It was leaking and I wasn't sure how to remove it as it's part of the engine, not a separate item like the saltwater pump.  I had a local German mechanic look at it (we’d used him before) and, on inspection, he pronounced it dead.  It was badly corroded and needed to be replaced with a new one.  This was at the start of the season at Preveza, Greece, and so we had to wait three weeks for the replacement part to be quoted, ordered and then delivered – from the US of course.  It took about an hour to put the pump on.  The generator ran fine thereafter.  I won’t mention the cost except to say that it was enormous, even the mechanic was embarrassed to tell us.

Time for a last swim at Jumping Fish Bay
Outboard Motor Not Starting.  Again, right at the start of the season, the outboard wouldn’t start, even though all was working fine at the end of the season when I run it until the carburetor ran out of fuel.  In hindsight, I should have run it in the yard before launching, but didn’t; an oversight on my part.  Anyway, after trying for some time I pulled the carburetor apart and inspected it for cleanliness.  It looked clean, but after I put it back on, it still wouldn’t start.  A kindly fellow on a nearby boat came over in his dinghy and freely offered advice, but despite his remedies, it still would not start.  Time for some searching on the web!  One useful piece of advice was that “a clean looking carbie does not necessarily mean it IS clean”.  This YouTuber advised to clean it to be sure, especially by inserting a thin wire into every orifice possible.  Well, I did this and the outboard started just fine.  So, big lesson here is that just because a carbie looks clean doesn’t mean it is and so do what I eventually did.  I’ll freely admit I did not see anything suspicious as I prodded and probed with my fine piece of wire.
  
Refrigerator Re-gassing.  Ahhh, yet again we had to have the refrigerator motor/evaporator re-gassed with the unusual hard-to-locate gas required for our Grunert 110 volt fridge.  Our reliable mechanic, although licenced, was not available so we contacted a local guy recommended by the marina.  Short story is he tried to rip us off by quoting and then trying to raise the price on the day.  Also, he tried to convince us to do more modifications than necessary.  Anyway, the fridge worked once it was re-gassed.  This little episode, apart from expensive now annual re-gassings, prompted much discussion on “a better way” to refrigerate given that our little WAECO battler was working brilliantly and running diligently on 12 volt sunshine power.

AIS.  We had purchased a GME AIST 120 and I fitted it next to the chart table, connected to our laptop via the program CD that came with it, and yet another antenna was fitted to the pushpit.  It works okey but we have since passed a number of ships at quite close range and there has been no signal received from them at all.  I certainly would not rely on it. 

There's more to follow....

Sad to be leaving our favourite Taverna over near Aktio

Sunday, February 28, 2016

2015: In the Marina & Loving It

Preveza Marina continued (Part 2):

Generator Coolant Water Pump.  The generator has a coolant system that you fill with antifreeze and this keeps the insides of the important bits of the engine cool.  Keeping the coolant cool is the job of the raw water that is circulated around the engine and spat out with the exhaust.  Well, this time it was the coolant water pump’s turn to fail.  Shortly after we set off on our trip north for Croatia there was clearly a major leak and gathering in the drip tray was all this coolant.  We returned to Preveza where our new best friend Stefan soon diagnosed the problem as being a failed coolant water pump ie it had corroded through its casing.  I thought that’s what the antifreeze coolant was supposed to stop.   Two weeks later, we had a new spare pump and fitted, at a modest cost that I still grit my teeth over – US parts imported into Europe means BIG money, mostly taxes.
This folks is what caused all the teeth gnashing, many weeks delay
and almost broke the annual cruising budget!!
Masthead Anchor Light.  This was working perfectly when we tested it shortly after we returned to the boat this year.  Once on anchor, however, we found it would not work, or would eventually.  After a trip up the mast to check the fitting and globe, when it seemed to work properly after some fiddling and testing, we then found that it would flash regularly rather than remain constant when turned on.  I still have no idea why it flashes but we just left it – it made it so very easy to identify our boat when returning to the anchorage at night time!  I might add, for all of you that are tut tutting, there are any number of combinations of anchor lights around Europe eg flashing single and multiple red and/or white lights at mastheads, in cockpits, tiny cheap solar lights that you can hardly see (especially when near a town with all their lights showing), and many boats without any anchor light at all.
There'll be a few more folks in town shopping today
Bike Repairs.  Our folding bikes are indispensable.  I’m surprised to see so many cruisers walking to/from/around town when they could be biking it.  Ours needed a service and a local Greek bike shop owner in Preveza did a wonderful job of restoring (read replacing) our fancy Shimano gears and generally fixing the bikes back to almost new.  We also lashed out and purchased some helmets.  The shop was a referral through Aktio.
Outboard Safety/Cut Off Switch.  Our Yamaha switch had given up the ghost some time ago although it would cut off when you pulled the clamp from the ignition.  Eventually it wouldn’t do that so I had to disconnect the switch, let it hang down and then use a coin or copper washer to make the electrical contact that would turn it off.  Tried to get a switch in Greece but not possible apparently.  Will get one in Oz and take it back overseas in 2016.
Ruins always seem conveniently located in Greece.
This is Nikopolis, Augustus's celebratory city just outside Preveza

Wednesday, February 24, 2016

2015: In the Marina & Keeping Busy

Preveza Marina: (Part 1)
A view over Preveza Marina.  Yes, another trip up the mast. 
To work out why the mast head light is still flashing...

Preveza in splendid summer colour
Making Life Easy.  In 2014, we'd discovered a neat trick.  Having spent too much time on the hard in boatyards over the years, we experimented with the options Preveza offered.  We'd found & booked space in the Preveza Marina a week prior to haul out.  Aside from its perfect location at the quiet end of the town, we could make most of our "leaving the boat" preparations with quite a few more conveniences.  Haul out was made with only a couple of days (not weeks or months!) on the hard before flying out.  This experience turned out so well, we gave it a shot again at the start of the season - only in reverse.  Splash after a few days then put-put over to the marina.  Perfect.
Generator Would Not Start.  I tried and tried but it started only after a lot of attempts.   I thought this was probably because the generator had been idle for eight months or may be the glow plugs weren’t quite right.  The next day when I tried, the engine would not turn over properly.  I cleaned all the terminals I could access and the engine started but then wouldn’t turn off when I pushed the cut off switch.  Finally, I managed to stop the engine by removing a ‘plug’ on the circuit board.  Time to call in the professionals! 

So, called on Stefan (yet again!) and, after an hour and a half of tracing circuits, looking at wiring diagrams, playing with switches, trying to start the engine without success, we found that the cut off wire goes via a water temperature sensor  on the engine block before it connects with the cut off terminal block.  This wire terminal at the temperature sensor had simply fallen off and so there was an interrupted circuit.  Once Stefan re-joined the wires all was as it should be and everything worked.  I have stated before that while cruising you meet some of the nicest people in the world that work on boats and Stefan is one of those.  He was so mortified that he didn’t find the fault quicker that he made his bill (we thought!) ridiculously cheap. He is also one of those people who is more than happy to explain exactly what he is doing and why, so I always learn heaps from these guys. 


Oh look!  Our new neighbour is another Hunter
Anti-Siphon Valve Broken.  Well, not quite.  I had retightened the hose clamp near the engine water inlet pump, several times, but it still leaked from there, or so I thought.  When we stopped in a marina we pulled the cover off the engine and, after starting the engine, it was soon plainly obvious that the water leak was coming from the siphon break, which sits a couple of feet above the raw water inlet hose.  One of the plastic fittings of the anti-siphon valve had sheared and it was slowly but constantly dripping water down on to the raw water inlet hose and then running along the bottom of the hose to the water pump.  Duh!  But what a coincidence – it never occurred to me that it could be anything but the newly fitted water hose.  Anyway, the broken siphon valve was easily replaced and all works without any water leak.  I might add that Stefan assisted with this discovery and repair too.

Sunday, February 21, 2016

2015: In the Yard & Keeping Busy

Preveza, Greece

Welcome to 2015....... Who'd a thought!

In the Yard
(The plan this year was to do a loop of the Adriatic ending back in Preveza.  Given all the work we'd done on WJ3, we figured on an "easy" prep time in the yard...  Of course you'd never believe that just didn't happen.  Our plans were delayed - big time - and we had to cut short the route.  Still, I'm probably not telling boat owners anything new.) 
All's quiet at Aktio
A view from on high
Engine Raw water inlet Hose.  Last year the hose started to leak and I taped it up (with you-beaut very stretchy silicone tape) so it no longer leaked.  Nevertheless, the hose was clearly failing so this year I replaced it, this time with clear stainless steel reinforced hose.  It runs cold water only as it is between the inlet raw water filter/strainer and the raw water engine pump.  This hose was different to the ‘black’ hose I threw out (which was also looking decidedly worse for wear and likely to leak in one or two other spots) but advice was that this clear hose was quite adequate for the job and, besides, you can observe the water in the hose.  So, as soon as it was fitted, would you believe, there was another water leak – water could be observed/felt dripping from the (new) inlet hose near the water pump.  See up-coming post for the result under Siphon Valve Broken.
Sewing.  The dodger, bimini and the dinghy boat cover needed extensive resewing of most seams plus some repairs to rips in the bimini.  Stitching has been the first to go on these coverings, unlike the acrylic which seems to last forever, and the more I repaired the more I found it needed work. 

It’s quite simple really, just pull on the area around a seam and, if the sewing comes apart easily, then it needs to be resewn.  I reckon I did most of the bimini and dodger.   Same for much of the dinghy cover. 

The (summer) awning also needed repairs and I discovered that ‘shade cloth aint shade cloth, Sol’.  Our shade cloth is easily chafed so I will replace it next year even though it’s only a few years old.  Many boats use shade cloth and they are not well supported on the boom etc and flap around madly, unlike our awning which was made to measure and is well secured to stays etc.  Nevertheless, they don’t seem to damage as readily as ours has done.
Baby donkey had grown quite a bit during our absence
Standing Rig Check.  Our insurers, Pantaenius, asked for a rig check as the rigging was now eight years old.  A local rigging company in Preveza duly obliged and the rig was thoroughly inspected over the space of an hour, no problems found and passed by insurance.  The riggers were a couple of local guys, as helpful as could be with all sorts of advice and just thoroughly nice blokes.  Their shop is located at Cleopatra Marina.
Chandlery.  We'd discovered Cleopatra Marina/Boatyard's well stocked chandlery and obliging staff on arrival in 2014.  And made very good use of it in 2015 too!
Another view over Preveza taken whilst servicing the mast
Can you just imagine Cleopatra & Augustus having a big boating battle in here!

Thursday, February 4, 2016

2014: Repairs Underway in Preveza

Ionian, Greece: 2014

Preveza Marina - getting ready for haul out
Companionway Step.  I managed to break the side lip on the bottom step of my companionway ladder while standing on it; replaced it with the top step and in turn had that replaced with a flat piece of timber (bamboo actually – a cutting board).  The original steps curl up at the edges and so they are particularly important on the bottom step as there is nothing else to stop one’s foot sliding sideways.  The other five above all have stainless railing to support your foot and prevent it sliding.  The companionway steps are one of our most loved parts of this boat ie a gentle rise, rather than a steep one like many other boats, and at rest it is quite easy/safe to carry a drink in each hand while ascending, without spilling anything.  I actually now prefer my new top step/cutting board as it is bigger than the original.  It’s fine at sea too.
Light Connections.  Located and repaired electric connections (that had come loose over time) for a bunch of cabin lights over the galley and in the store room.
 
Floating through the Corinth Canal
Leaking Fresh Water Tank.   For several seasons I had always wondered as to why there was water pumped from the bilge whenever we refilled the water tanks.  It only occurred a few of times then it would stop altogether.  To cut a long story short this year I heard a strange sound while refilling the water tanks and lifted some of the flooring access plates.  I could hear a hissing gurgling sound and sure enough one of the (five) plastic water tanks had a small slit at its top.  

I could feel it but not see it as most of the water tanks are hidden from view under furniture.  As it is, I can’t get to it to repair it and would have to lift some flooring and may be some of the galley furniture (which is not removable as far as I can see) to be able to do so.  I believe that you can repair these tanks with plastic welding but you need to be able to get to the damaged part relatively easily.  It looks easy on You Tube.  So, I’ve had to leave it and I use this tank first off whenever I refill tanks.  Fortunately all tanks can be isolated from each other using the ball valves for each tank located near the fresh water pump.

Starter Battery Died.  At the island of Meganissi, on the Ionian Sea and not very far south of Preveza, the starter battery died.  Working fine one day, not the next.  Fortunately, Meganissi was only a 20 minute fast dinghy hike in Bruce to a decent chandlery on Lefkadha and I was back on the boat in an hour and a half with a brand new battery.  No further problems.  I did try to use jumper leads from the storage batteries to the starter battery but it was not enough to turn the engine over.  I’m sure there must be another solution and will let you know when I find it out.  What if one were far away from civilization and the starter battery died?
At the marina, we had time for side trips
Maintaining Stainless Steel.  This year I made a startling discovery.  To keep the stainless clean and shiny, with minimum rust marks, clean it with fresh water.  It gets very salt encrusted as you cruise around and builds up rust stains but, rather than leave it until the end of the season or on visits to marinas where there is plenty of fresh water to hose them off, just wipe them with a wet rag of fresh water every now and again.  We carry four jerry cans of spare fresh water but you really don’t need to use much anyway.  A bucket half full will easily cover all the (considerable) stainless railing around the boat.  Anyway, just remarkable, no need for polishing all the time (which I rarely do although I always feel guilty for not doing it).  I suppose everyone else out there knows this simple technique but I had never read about it.  I just discovered it by accident. 

Generator Raw Water Develops Galloping Diarrhoea.   About a week or so before we reached our port of storage at the end of the season (Preveza), the generator shat itself and the drip tray was full of dirty brown water.  The raw water pump bearing had died again (last time seven years ago) and so it was leaking lots of water from the engine cooling system.  No other damage resulted as water was still being circulated around the engine but the generator could no longer be used.  We had it repaired once we were on the hard by a very helpful German mechanic, Stefan, arranged for by the yard – Aktio Marina.  This was to be the beginning of a growing but unwelcome relationship - only because of too many boat bits needing TLC!  Our relationship continued on in 2015.  The Other Woman is loving the attention....

2014 - an Interesting year for repairs!
Aktio Boatyard, Preveza - Haul Out

Thursday, January 21, 2016

2014: More Repairs in the Marina

Marmaris, Turkey: Part 2
Work in the Boatyard continues....

Anemometer Smashed.  On checking our electrics etc after returning to the boat I noticed that the anemometer (wind meter) was not showing any reading.  It was on at the screen but not indicating any reading of wind speed or direction.  On checking the masthead through the binoculars I couldn't see it.  I climbed the mast only to find the plug all by itself without the usual staff, with windcups and wind vane completely gone.  I made enquiries of the locals and was informed of a massive hail storm experienced some months beforehand and presumably the wind vane was cleanly knocked off the masthead.  It wasn’t difficult to source a new one and install it.  Just another expense!
Although it doesn't look like it, a storm of 30kts blew over soon after we
arrived at the anchorage off Yat Marin at Marmaris.  Welcome to boating!
And I hope everything is working, including the anchor....

VHF Antenna.  I had previously noticed that our handheld VHF radio had a better range than the mounted VHF radio.  Turned out, after a lot of checking, that the cable plug where it entered the back of the radio had lost its solder from its core.  Our antenna cable has a join at the base of the mast so I only had to remove the cable between radio and mast (thank goodness) and not the cable going up the mast to the masthead antenna.  Had it repaired by a friendly local technician (a lady) in a local shop at the marina, reinstalled it and everything ok again. 
Window Screens.  Our two forward fixed deck windows have mesh screens permanently in place, attached with press studs, which do a superb job, in addition to the tinted windows, in keeping light to a comfortable level inside the main cabin. They were old and needing repair so had them copied by a canvas maker in Marmaris town proper. A superb job & the screens fitted perfectly. 
Marmaris for Work Done on Boats.  Marmaris is probably one of the best places we have had work done in all the places we have been to ie a balance of fair quality work for a very reasonable price, bearing in mind my other observations.  There are plenty of tradespeople to choose from and so there is good competition even at the Yat Marin Marina.  If you didn’t like one or two quotes there were others to approach.  You can actually get firm quotes although in one case one quote was only an approximation which turned out to be much less than the bill ie regassing the fridge in 2013.  The quotes did vary markedly so this is a great place to shop around.  There are also a heap of yacht services in Marmaris town but you either approach them directly or you need to get permission from the marina before they are allowed to work on your boat at the marina, which in our case wasn’t necessary.

Off Datca under a full moon
 

Monday, January 11, 2016

2014: Repairs in the Marina

Marmaris, Turkey: Part 1

(Finally there's a bit of time to update the H460 blog...between bouts of boat maintenance and house renovations!)

Life on the Hard - with unsurpassed views
Sails Cleaned and UV Stitching Replaced.  I took up an offer at the marina sailmakers in 2013 to have the sails washed and inspected when we stored the boat on the hard in Marmaris.  It was all quoted and we left the sails with the sailmaker to pick up on return in 2014.  I left a deposit (payment of 50% was what the rules said) and, I noted accordingly on their invoice as the sailmaker doing the paperwork said she was not going to issue a receipt just now but when I paid fully next year.  Okey, when in Rome …  To cut a long story short, when I went to pick up the sails she denied any payment having been made.  I pointed out my note and she said ‘this has never happened before … la la la … but I was not backing down.  So, she reluctantly accepted my point and the balance.  I complained to the sailmaker manager only to find out that everyone working there is family so no real point taking it further with that lot.  I was quite prepared to take it up with the marina manager but not really necessary as it turned out. 
All the stitching on the UV covers was redone however, so overall I got what I paid for.  Big lesson, whenever making a payment always get some receipt or, if in Greece where they don’t know about receipts, make some note of any payments, like I did with this lot.
Bike Bags.  Before our falling out I had also purchased a couple of big old sail bags quite cheaply and we use them to store our bikes in – much neater and good protection from the elements as we put the bikes in the dinghy on its davits when sailing.
I also needed my continuous furling line replaced but, at this stage, the sailmaker was not interested, for obvious reasons.  For my solution, see below.
I should also have included the webbing on the clew of the mainsail to be restitched, but didn’t (my fault) and paid the price - more on that later too.
 
A very professional launch in Marmaris
Boat Detailing.  At the marina, very shortly after being placed in a cradle on the hard in 2013, I was quickly approached by a few of the private tradespeople that occupy their own workshops around the wall of the marina.  I accepted one quote to polish the topsides and stainless steel and also to undertake professional gelcoat repairs to hairline cracks and other minor scratches and repairs that have appeared over the years on the deck and topsides.  It also included one coat of antifouling to the bottom and he also raised the waterline around the stern as requested.  All for a very reasonable price.  He also undertook to wash the boat down each month while we were at home and that he would let me know when he had done so each time.  He gave me contact details of previous customers whom I contacted and they were generally pleased with his work.  One said don’t make the final payment until the boat is back in the water as his staff did not do the final anti fouling on the spots on the hull that can’t be done while the boat is in its cradle.  As it turned out on the launch day it was more convenient for me to do it myself anyway.
All the work was carried out as promised except I had to chase him up about the wash downs each month.  When I did enquire he answered promptly and also gave me updates on the work to be, and being, done.  He only required a very small deposit before I left, a part payment shortly after I returned, and then the balance on completion of all the work ie when the last dabs of paint were put on when the boat was picked up for relaunching .  Highly recommended providing you take an ongoing interest in progress etc.
Turkey's coast is a picture postcard delight

Sunday, December 15, 2013

2013: Year 6 - Work in Lagos

Sopromar Boatyard:
Time to get our hands dirty again!
Bow Thruster.  I’ve just lashed out and had a new one fitted in the bow – I would have liked to have both a bow and stern thruster but the boat doesn’t have enough room in the stern – too much other stuff.  I’ve been sort of avoiding fitting a bow thruster, almost as a matter of pride (plus they’re not cheap) and, after I’ve bumped my way around a marina, I could always say “well, I don’t have a bow thruster like you people.”  I’ve also seen a number of times skippers playing with their bow thrusters, and at the same time getting into difficulties, when they should just be motoring forward into their berth.  However, just about everyone I’ve met that has a bow thruster seems to swear by them.  So, providing mine works okey I’ll not have any more excuses when manoeuvring in and out of marinas.  Its been professionally fitted at Sopromar Boatyard.  No fuss!
We arrived to a new bow thruster (WJ3's now sprouting nostrils)
Spinnaker Furler.  We have a cruising chute which hasn’t been getting enough use because it’s contained in a sock (which is good) but requires a bit of work to set and take down.  We can both envision me getting wrapped up in a chute, going overboard and Galley Slave left to sort everything out, return to pick me up and us both being terribly traumatized by the whole event.  Much better to do everything from the cockpit, just like we (almost) do now.  So, I’m presently trying to purchase a spinnaker furler, which is not as easy as it sounds.  Anti-torsion lines are a real problem to obtain apparently and so I’ve been trying to make this purchase for a couple of months now.   I’ll report on how things turn out later on.
Even Bruce got some attention this year!

And we had time for some local siteseeing

Before Launch Day arrived
(& our mission this year - to cross to Turkey)