Showing posts with label Deltaville. Show all posts
Showing posts with label Deltaville. Show all posts

Sunday, December 8, 2013

2011: A Late Start

Crossing the Atlantic

Repairs Underway: Part 1

Generally, all repairs & modifications took place before we left Deltaville Boatyard. We were thankful for the assistance provided by the Yard’s skilled technicians and their quality work.  
Our plan was to head north to New York City, or thereabouts, then head east to Europe along the 40th parallel.  Simple, until we reached Baltimore and I carried out a last minute check of some of our gear…. 

Rudder Steering Arm.  On inspection I discovered two cracks in the rudder fitting – steering arm if memory serves me correctly - at the top of the rudder stock and which was attached to the steering via push rods.  Serious stuff and my discovery brought back many memories of the new rudder being fitted in the British Virgin Islands in 2008.  At the time the new rudder’s stock was ever so slightly smaller than the old one and so the old steering arm needed to be fitted accordingly.  At the time the ‘technician’ did this by belting the living daylights out of the (cast) fitting with a hammer until it eventually cracked.  Two weldings later and some shims had it all fitted okey.  Not.  Time had caught up with it and the steering arm had failed along the line of the weld.  So I decided, given our Atlantic crossing plans, it was time to fit a brand new one.
Cracked rudder steering arm
After some discussion in Baltimore & Annapolis at various yards, we hoofed it back to Deltaville, reasoning that they understood us and our boat.  Kindly they responded to our short time line (we really needed to get going on our crossing) where they measured the rudder stock precisely and a new fitting was ordered.  It’s interesting to note that Edson, the supplier, needed a reading that was accurate to within three thousandths of an inch.  On being given these dimensions they then bore the hole in the fitting.  It fitted perfectly and is still doing sterling service.
 
Hauling out at short notice
More Steering Breakages.  At this late stage we decided to sail south a relatively short distance to Norfolk, at the southern end of the Chesapeake Bay, and then head off for Europe from there.  The first night out, as you do, we had a fine gale which was quite unexpected.  We also lost autopilot steering when the cog, on the other end of the shaft that the steering wheel is fitted to, sheared so that the chain to the autopilot motor was completely disconnected. 

Unhappily, but not wanting to steer all the way across the Atlantic, we turned back to Norfolk, ordered a new replacement shaft, had the broken one repaired too, fitted the new shaft and autopilot chain, then headed north to New York City (again). 

As we had no further problems we then headed east for Europe via the Azores. As you do!
Some of the crew added their own modifications
which came with a drinks service too!

Saturday, March 16, 2013

2011: Still Repairing at the Marina

Deltaville Marina: Part 3
Trying to check the Nav when it's bucketing
Dodger Side Curtains.  We had had made for us, some years ago in the Caribbean, side curtains of shade cloth  for the bimini – I have written about them before in glowing terms.  Between the bimini and dodger there is also a joining piece and there are side curtains for that as well.  These particular side curtains are great but don’t keep out the sea when bashing to windward, for example.  So I made some sunbrella screens that we clip onto these side curtains when sailing in wet weather – they did the job and kept out a lot of water that would otherwise have wet us in the cockpit.
All hands use the canvas machine...
Locking the Steering Wheel.  We have a Hydrovane wind vane self-steering gear that steers the boat all by itself and the main rudder steering is locked.  I have a steering lock as part of the wheel steering arrangement and, to be frank, it has never worked well ie it’s pretty weak and one can fairly easily turn the wheel by hand.  You also have to rotate the knob on the break which is very slow to take up.  I therefore came up with a block and tackle arrangement, quite light weight as the steering is quite light, which I will try to describe here.
I attached with chord a block with cam cleat to each side of the steering wheel and shackled two other blocks (one for each side) to a u bolt that I bolted to the cockpit floor at the middle base of the steering pedestal.  I ran lines connecting the respective blocks at the bottom of the pedestal  to the blocks on each side of the steering wheel.  I could lock the steering wheel centrally in an instant by using the cam cleats and, just as easily, make slight adjustments to the wheel to allow, for example, weather helm.  All this is necessary to balance the boat as best you can so that Mr Hydrovane can steer the boat with his (much smaller) rudder.  It is also easy to disconnect the steering lock and steer the boat using the wheel if, say, you need to manoeuvre quickly to avoid something. 
With the Hydrovane fitted, ready for some blue water action

Though not all the crew were taking this up-coming voyage (Atlantic Crossing) seriously..

Saturday, June 25, 2011

2011: More Repairs at the Marina

Deltaville Marina: Part 2

f.  Fridge.  The fridge stopped working after the Mate cleaned it last year – the freezer soldiered on as though nothing had happened.  The fridge had a new pressure valve installed ($300 thank you) and the whole system will have to be re-gassed by a technician.  An expensive fix but essential for crew morale (and the Captain’s appetite! Ed.).

g.  Engine Raw Water Impellers.  I replaced both the engine and generator water impellers, because it was suggested by some around here that this was a wise precaution to do each and every year.  I wasn’t convinced until I found that both of them each had a flap missing.  So, there you go, change them annually whether they need it or not, even if the owner's manual says otherwise or at least remove and inspect them for any damage, before replacing them.  Don’t forget the lubricant before you replace them. 

I also use a special impeller removing tool but there is insufficient room to be able to use the turning handle that it comes with – other engine bits and pieces get in the way.  Nevertheless, just being able to grasp the impeller with the two ‘arms’ is enough to get a decent grip on the impeller so that I can wiggle it out of the engine just using my hand.  I also have to lay on top of the engine when I do this and I can hardly see – all done by feel as the impeller faces aft and is on the side of the engine.  My generator has its water pump mounted on its front which, comparatively, makes it a joy to change impellers.

Installing antenna for HF radio - more RAT shots!
And Mast Steps come in handy too.
h.  Generator Raw Water Hose.  I had been watching this hose ever since I purchased the boat.  It seemed to be okay but, this year, I thought I would treat our venerable and hard working generator with a new hose.  Well, I replaced it with another new one of exactly the same size – 5/8’’ only to find that, on testing, it sucked its insides together, obviously seriously restricting water flow.  I then checked the fittings on the strainer and generator only to find they were ¾’’, not 5/8’’.  So, I replaced it with another new steel-reinforced ¾’’ hose and it works a treat – the generator loves me again.  I also replaced/tightened a couple of the other hose clips which had been allowing a few drips of water to escape.

i.  Primary Engine Fuel Filter Fittings.  R2D2 no longer looks like something from outer space; he is settled in looking more like a new filter with brand new elbow fuel line fittings. 

j.  Fridge Raw Water Strainer.  I replaced the wire strainer for the fridge – not a simple task as there are no brand names on these housings, so I had to purchase a complete fitting with some spare screens.  Screens also come with different sized openings so there you go.  Remember that you measure the size of the inside diameter of the hose that attaches to it ie ¾’’ in this case, not the 1’’ on the outside of the thread.  Needless to say, I got it wrong first off before realizing my mistake when the 1’’ strainer arrived and it was way too big.

Friday, June 24, 2011

2011: Repairs at the Marina

Deltaville Marina: Part 1

At some point we realised just how useful it is to have time at the dock rather than trying to do it all on the hard, particularly when it comes to adjusting or finetuning all this expensive gear we have on board.  So after we splash, we head to the dock for a few days at least.  In 2011, we spent quite some time there.  After all, we were prepping for an Atlantic Crossing.  So, everything needed to work perfectly!     

a.  Freshwater System.  A couple of those PVC fittings broke so a lot of freshwater ended up in the bilge as I filled water tanks and then turned on the pressure water system.  A breather line came away from the hull fitting sending more freshwater into the bilge and I had to add a short extension to the original hose.  Oh well, the bilges love a bit of fresh water circulated through them. 

b.  Manual Toilet.  The two anti-syphon valves on the inlet and outlet lines to the manual toilet decided to fail at the same time so I had to replace them.  No leaks now, which has made the whole thing much more ‘attractive’. 
More motoring up the Chesapeake with BW at the helm
c.  Forward Bathroom Hatch Rebedded.  The acrylic had come away from the hatch frame and so I rebedded it with 3M 5200.  It’s quite heavy since I added the Nicro solar vent to ventilate the compost toilet and, I think, there may have been too much weight for the sealant to adequately hold the acrylic in place.  So far it’s doing what it should.
 
d.  Regalvanize Anchor Chain and Second Anchor.  The chain and second anchor were quite rusted in places so I was able to get it all regalvanised at Ashland near Richmond.  They did a good job and it cost about a third of a new chain.  Since my chain was not that old nor showing any obvious signs of excessive wear, this seemed like a sensible solution.  All we have to do now is mark the various depths (with cable ties) and then put it all back on board.
 
(For anyone interested, BW scored the job of marking off the chain.  He chose to measure it in 10ft lengths and fold it in 30ft lengths.  Every 30ft length, over the entire length of chain, is marked with cable ties - yellow @ 10ft; orange @ 20ft; and red @ 30ft; starting yellow @ 40; orange @ 50 and so on until the entire length of chain is cabled with these three colours.  Then, each 30ft is marked as well.  We started with blue cable ties.  One @ 30ft; two @ 60ft; and three @ 90 ft, then repeated the same with green to mark the next three lengths.  It sounds complicated but as the chain is running out over the anchor winch - even in torchlight - you can be sure that you know exactly how much is out. We haven't had too many cable ties pop off either.)
 
e.  Spinnaker Pole End Fittings.  I purchased two new Ronstan spinnaker pole ends and Crew put them on the pole, after I broke one of them (a plastic fitting - not Ronstan) last year in a simple and not particularly stressful situation.  The fittings I purchased in Australia, brought them with me, then found that there was one or two millimetres difference in diameter of the pole and Ronstan fittings.  My Crew had to grind some of the raised sections down and then they fitted perfectly.  These aluminium fittings are much more robust than the ones they replaced.
First flight - new spinnaker feels the breeze
on Chesapeake Bay

Thursday, June 23, 2011

2011: More Work in the Boatyard

Deltaville Boatyard: Part 2

Series Drogue.  I purchased this last year but, since we only coastal cruised, never got around to attaching any of the 138 drogues to the line.  This is a job to be done before we leave the Chesapeake this year and so many hours, while cruising northwards up the Bay were spent sitting on the back of the boat seemingly endlessly attaching drogues to the line.   It's a simple task and only took a "few" days - I could almost do it in my sleep now.  I only dropped one splicing tool overboard but happened to have a suitable substitute so work continued.  Anyway, the next issue was to decide how to attach the gear to the stern and without pulling the stern off/apart when using the drogue seriously.

Apparently, in a full gale/storm, the forces exerted along the line, and by extension via the bridle onto the boat, can be quite enormous.  So, where to attach the two ends of the bridle?  Some publications advise fixing special reinforced points around the stern, however, in my view, this seemed like a lot of hard work and best avoided if another solution could be found.  My erstwhile son, Boy Wonder, is a RAT (rope access technician – does outside repairs on tall buildings/towers while hanging from ropes) and he suggested a number of lines could be taken from various already-reinforced points around the cockpit ie six winches and two mooring cleats.  By using various sheet and halyard lines/tails already positioned around the cockpit they could be easily attached to the ends of the bridle from the winches and cleats so that there would be something like four lines per bridle end.  Hence any loads are spread about and there is excellent control via the winches so that their lines at least can be equally tensioned.   I haven’t had to test it, thank goodness, but I’m still of a view that it’s a sensible and strong solution.
A good view of the solar panels on the bimini, the self steering post
in place & a RAT (BW) up the mast installing the antenna
Third Solar Panel.  After last year’s experience with our two solar panels we’ve been converted to using this energy source and, as there was room for one more panel between the other two, I purchased another.  The advice from e Marine Systems was that I might exceed the regulator’s capacity of 25 amps but that would only be when the system was producing max amps ie perhaps 28 amps and so I may not get that surplus three amps to the batteries.  My experience was that two produced, for my setup at best, 16 amps so a third would only increase it to, perhaps, 24 amps.  Anyway, we’ll see.  It was a simple task to put in the third, wire it in parallel with the others, and the wiring was adequate for my needs as advised by the yard technicians.  These panels really are great and the more the merrier.

HF Radio.  After much thinking, discussion, research, skipper and crew decided, for a variety of reasons, that we should have a HF radio for the upcoming Atlantic crossing.  So, I purchased and installed an Icom M802 radio plus weather fax system.  It has DSC too so that added the odd complication.  Anyway, it came as a kit from Sea Tech so I didn’t have any problems with wiring or fittings as they were all there (just about) and staff were ever willing to provide friendly advice as and when I needed it.  It’s all installed now so we’ll see how it performs (see comments later). 

I went down the route of installing a KISS SSB ground counterpoise and a GAM antenna which ‘clips’ onto the starboard shroud.  This system is counter to some of the conventional/traditional readings and writings on HF radio grounding etc but, on the other hand, I have read good reports about this kit.  So, for anyone contemplating installing a HF radio, read widely and then make your decisions, knowing that there are so-called experts out there that might disagree with your solution.  You would think by now that we boaties would have our act together on this but, clearly, we don’t. 


Bedding down the HF antenna
Spinnaker Winches.  I found a couple of second-hand Lewmar 44 sheet winches looking for a new owner on the shelves at Nauti Nell’s in Deltaville.  I’d been contemplating adding a couple of cockpit winches to make life easier handling the new spinnaker sheets, furling lines on occasion, etc but had been put off a bit at the price of purchasing new ones.  These two used ones were too good to resist so they are about to be installed on the cockpit coamings.  I’ll comment later on their utility.

Wednesday, June 22, 2011

2011: Year 4 - Work in the Boatyard

Deltaville Boatyard: Part 1

Let me begin by saying that I arrived back to a sweet smelling boat – our winterizing last year had worked well and there was no mould.  Also the teak oil we used (Starbright) was more robust and has really made all the internal wood work look much improved.

I Don't Think I Need Any More Stuff.  Now, I think I’m approaching the point where I just can’t put anything else on or into the boat.  June 2011 has to be the turning point where I’ll finish adding stuff and only look after maintenance, or may be occasionally replace some thing with a new better thing.  Also we have plans to sail from the US to Portugal via the Azores, so I’m doing a check of all our safety and storm gear before we leave.  Of course, all you Old Salts out there will know that there is always more gear to be added to a boat and so I have to eat humble pie here.  Read on to find out about "new better things" I've since added.  (Ed. No more stuff?  Hysterical laughter begins....)

Home Preparatory Courses.  I started our preparation at home by having us all attend a Sea Survival course with Gerry Fitzgerald, Offshore Marine Training.  Further to this I also did a radar course to try to understand my electronic system better.  Both GS & Boy Wonder decided to get their Marine Radio Licences and then do a Marine First Aid Course to cover any eventuality. 

We ordered this at the Annapolis Boat Show
Sails.  We didn’t ever set our new 2010 spinnaker or attach the hanks to the storm trysail, but we will this year.  I have new sheets for the spinnaker and a deck line for the tack to be adjusted from the cockpit.  The trysail has its hanks attached and had a trial hoist before we leave the Chesapeake for Europe.  Meanwhile, I purchased a storm jib – the Storm Bag, which came from France.  This sail comes, with its own sheets, in a saddle bag arrangement which you place around the furled jib/genoa.  You then attach the (spare) halyard to the head, clip the tack to a bow deck fitting and make sure the sheets are clipped together at the clew, and hoist away from the safety of the cockpit, then trim to suit.  Seems a simple solution to setting a storm jib over furled sails, provides a reserve sail in case of damage to the genoa and/or staysail, and minimizes the amount of time on the foredeck in high winds.  I ordered one that was a size smaller in area (not in sailcloth weight) than recommended because I have the staysail which I will use for as long as I can before resorting to the storm jib.

Saturday, June 18, 2011

Winterising Decisions

Grand Designs: 2010

We tossed and turned about our 2010 winterising location and did quite some research into leaving WJ3 in Nova Scotia.  This would have meant a more relaxed, thorough trip north from Chesapeake Bay to Maine and Nova Scotia.  We had even hoped to make Prince Edward Island too.  However, we ended up returning to Deltaville largely due to the commitment of winterising that far north.  This saved us the hassle of finding a wooden cradle, taking out the mast, covering WJ3 in plastic shrink wrap (friend Paula reckons they look like oversized Steggles frozen chickens!) and/or leaving her in heated accommodation.  We would then have further problems of sailing through ice on our way out to the Azores. These cold weather solutions did not appeal to us at all and our concerns were well-substantiated when a friend (who loves cold water sailing) did leave his boat with associated costs to the tune of some $17000. Mind, that did include some work done to the mast whist it was out.

Chilly on the Chesapeake in late October
Back in Deltaville, we allowed a good ten days to get those chores done before leaving WJ3 to Virginian snows and icy blasts – and as we were later to discover some rather too close tornadoes. 

After last year’s mould problem, we still washed the hard areas down with a vinegar/water solution and left baking powder in the fridges to keep them smelling sweet.  GS put a generous quantity of closet camels throughout the boat and sprinkled lockers liberally with moth balls.  I consulted Herd’s Hardware (a great local repository of gadgets, knowledge and advice) as to a better solution to our teak oil problems.  Finally I set up one dorade vent just behind the mast (in a purpose built fitting) and left the small solar fan that vents the compost loo (disconnected) to extract stale air from the boat. Let’s see if that works!

Tuesday, June 14, 2011

2010: Even More Work in Deltaville

Deltaville Boatyard: Part 3

Waeco Fridge/Freezer. 
We can’t use our fridge and freezer out of the water as they use 110 volt and need sea water circulating around the system.  So, since we do spend a bit of time on the hard we wanted some refrigeration rather than relying on bags of ice to keep our essentials fresh and beer cold.  Our friends on Paradise had a small Waeco and recommended it so I purchased and installed one in the spare/storage room.  It operates on 240, 110, 12 or 24 volts, whatever is available to it.  You can set it as a freezer or fridge, or anything in between.  It’s been a godsend and we love it.
Adding & adjusting the new solar panels
Solar Panels.  To assist our batteries we installed 2x135watt solar panels on the stern just behind the arch. I purchased a kit to come with the panels and had a technician install the wiring, regulator, etc.  I mounted the panels on a frame system that was built by a stainless fabricator.  He had a better design than the one provided in the kit so I ended up with some stainless fittings surplus to requirement.  The frame is mounted to the arch and the bimini so it’s pretty substantial.  The stern area of WJ3 now looks a bit like a meccano set.  On a good day now I can get 16amps belting into the batteries from the two panels.

Engine Service.  A 3000 hours major service was given for the Yanmar engine.  The mechanic, while carrying out the service, showed me all sorts of stuff including the removal and testing of the injectors.  The service was mainly done in the water, which they prefer, and it also included a sea trial and an alignment check for the propeller shaft.  Most hoses and hose clamps were replaced and the turbo charger cleaned with some secret liquid potion.  The mechanic was very good at what he does and, as always, I enjoyed our general chat about life in America.
Snug in Deltaville Marina
Charts. We both had our personal laptops loaded with CMaps charts and found, with a GPS installed, this to be an effective navigation system.  We did back up with chartbooks however.  I don’t think we could have survived the ICW without a little bit of specific knowledge.

We picked up some cruising charts and guides along the way as there is usually a trading table/assortment of freebies or cheap second hand offers in the mariners lounge at each marina. Otherwise we did supplement our stash with a few good reference books and travel guides to get the most out of each location we visited.  I’ll do up a list in a later blog of the charts and guides we found most useful during our sailing seasons to date.

SkyMate.  In August 2010 we installed a SkyMate system after it was recommended by fellow Aussies Bev & Greg on Liberty VI (another Hunter 460 in the Deltaville Boatyard).  It’s basically a satellite system whereby you can receive weather information whenever you ask for it irrespective of wherever you are, at least that’s the theory.  It will also report your position and is available for other people to know where you are.  You can also send and receive basic email messages.  It might do other things but that is what we purchased it for.  I installed it myself, ie a VHF antenna mounted on the pulpit, a ‘black box’ in the chart table panel, and this is connected to your computer.  It worked quite well most of the time but, a major drawback, is that you have to inform them when you are crossing their boundaries so that they can make sure you are covered. 

Monday, June 13, 2011

2010: More Work in Deltaville

Deltaville Boatyard: Part 2

Outboard Hoist near Davits
Sail Wardrobe.  Plans were being hatched in 2009 for a storm trysail and cruising spinnaker when finances allow and these were added in 2010.  I ordered, via the internet and while in Australia, a cruising spinnaker and a storm trysail from the Rolly Tasker agent in the US, which were waiting for us on our arrival at the boatyard in Deltaville.  Couldn’t have been much easier!  I also did the same for a series drogue from Sailrite.

Outboard Hoist.  In Deltaville there is a shop - Nauti Nell’s - that, among other nautical nick-knacks, sells boat items on consignment.  We love visiting this place and, shortly after returning in 2010, I found an outboard hoist at a bargain price ie half new but the item was indeed new.  So, we now have a heavy duty stainless lifting hoist on the back of the boat, which has made lifting the heavy 15hp outboard a relative breeze.

Washdown Pump and Hose
Washdown Pump.  My Crew (anchor woman) called for a washdown pump (salt water) to be provided mainly for those occasions when the anchor is pulled up and covered in thick oozy clinging mud, which has been most of the trip since we entered the ICW at West Palm Beach in 2009.  When I installed the compost toilet up forward it freed up the toilet intake raw water pipe and so I installed a washdown pump in line, put in a deck fitting in the deck, and plumbed everything.  Electric wiring was provided by the, no-longer-needed, wiring for the forward holding tank pump.  So, a relatively simple task (once I had worked it all out) has made up-anchoring almost a pleasure for the First Mate.  Cost - about $200 by doing it myself.  I bought the long hose kit (50’) so that I could easily get to anywhere on the boat if needs be, and especially the stern when, one day, we catch a big fish and need to wash away the mess after cleaning it.  One has to have a dream!

Radar.  I purchased and installed a Furuno radar, attaching the antenna just above the lower spreaders. This was another internet purchase.  I must say that the Boat Yard were very good at taking deliveries for those of us who DIY.  I set the radar screen/panel just above the chart table and, yes, some would say that it should be at the helm in the cockpit but I prefer my navigation electronics at the chart table.
The new radar (WJ3 in the Deltaville Marina)
Freshwater Plumbing.  The pressure freshwater system uses a fairly common PVC system (available in most hardware stores in the US) whereby hoses are routed and joined using a range of press-on-and-screw fittings.  It works quite well but the fittings do tend to crack – perhaps it’s just old age or they might be too tight perhaps.  So, I have had to replace a number of them as they leak when they crack.  So, I monitor the freshwater system fairly regularly and listen for any intermittent noises from the pump, which might indicate that there is a leak somewhere. I also carry a range of spares and check said fittings to ensure they do not work loose with vibration of the pipes over time.

Sunday, June 12, 2011

2010: Year 3 - Work in Deltaville

Deltaville Boatyard: Part 1

Back in the USA.  Deltaville is beginning to feel like home!
 
Winterising in 2009 worked effectively but we spent a good few days cleaning mould off the timber work. We had used a light furniture oil to treat it before we left.  The hard surfaces we treated with a vinegar solution and that seemed to work very well except for the shower (because we left the door closed).  We needed to consider a ventilation system before leaving WJ3 in the boatyard at the end of the 2010 cruising season.

Full frosty moon in the boatyard
‘Essential’ Upgrades and Repairs.  I decided to spend time in the Deltaville boatyard before splashing to get all those “essential” upgrades and repairs attended to.  In all we became a regular part of the Deltaville community in our 6 weeks up on the hard and 4 weeks in the Marina.  We concluded that life was a lot easier in the water (and nearer to the pool, laundry and bathhouse!).  However, this delayed our departure for Maine & New England coasts until well into the season and we had to strike Nova Scotia off our list all together.  We both agreed though that the time spent doing maintenance and upgrades was well worth it and the First Mate even found a local quilting group to visit. This is what we did:

Toilets and Being Green.  The macerator pumps needed to be replaced as the original ones were corroded and not working, so we just swapped one for one, easy.  I had an impromptu test of one of them when my Crew mistakenly filled a holding tank with fresh water, rather than the nearby fresh water tank.  Oh well! 

  
Oh look.  An outside dunny!
We actually took this one step further and took out a complete head system (in the forward cabin) and replaced it with an eco composting toilet aka “turdis”.  Simple, easy to use (we hope) and so far the only problem we’ve heard is that peat moss – the necessary composting agent – is hard to find in some places.  However, peat moss comes in huge bags so that we now have a couple of tubs full in the storeroom – probably 10 years worth at our rate.  

This loo, a Natures Head, complies with strict US regulations regarding discharge but best of all (so the cranky crew says) it can be used whilst we are up on the hard.  The rear head, easiest to use whilst at sea, remains a pump out or holding tank choice depending on where we are. 

The compost toilet has turned out to be a most welcome item – next to no smells as there is a small (computer type) fan that constantly circulates the air inside the toilet to outside the cabin, via a tube system from the toilet to a deck fitting.  The fan can be wired into the boat’s electric system or you can use, as we do, a solar powered vent, which runs all day in sunlight and, at night, runs off a recharged rechargeable battery.

Sunday, June 5, 2011

Journey's End 2009


Crab Crackin' at Deltaville Marina
Jackson Creek, Deltaville: 2009

Deltaville.  We planned to leave WJ3 for the winter in Deltaville, and as it can get cold this far north, we spent about two weeks before departure cleaning and winterising her.  As winterising was a new concept for us (lucky Aussies aren’t we) we had the engine properly serviced whilst I observed and took lots of notes, and then did the rest ourselves.  The staff at the Deltaville Boatyard were more than helpful.  I connected a small solar panel to the batteries while the boat was laid up. All this prep work took us a good 10 days, most of the time living on the boat on the hard.  Although this had its down side, we did get to meet a few fellow travellers in the Marina Lounge. Having covered a distance from Trinidad to Deltaville, some 2789nm, we flew home end of September 2009 more than pleased with our efforts.
Thar She Blow's!  Hauling out is always an unnerving experience...